AIR-AP2802E-QK910C Cisco Aironet 2800e 4x4:3 MU-MIMO WiFi 5 10 APs

AIR-AP2802E-QK910C exact order identity

AIR-AP2802E-QK910C is a Cisco Aironet 2800 Series controller-based 802.11ac Wave 2 access point order. The exact line combines a 2802E indoor access point for external antennas, regulatory-domain token Q, and a configurable ten-unit eco-pack.

Antenna boundary

Cisco documents four RP-TNC antenna connectors plus a Smart Antenna connector on the 2802E. Antennas are a separate engineered part of the deployment bill of materials. Before release, record each Cisco-supported antenna part number, connector use, gain, pattern, cable type, cable loss, mounting orientation and local approval. A connector fit alone does not establish RF performance or regulatory suitability.

Order-form boundary

Cisco's ordering convention uses K910C for a configurable ten-access-point eco-pack. Configuration selection and physical quantity are separate acceptance gates: the chosen domain must be approved and ten individual units must be reconciled. Retain the configured-domain evidence with the carton record, then create ten serial-level asset rows. Do not release a partial, mixed-domain or unconfigured carton to installation without a documented correction. Because this is a configurable line, purchasing must retain the finally selected domain on both the authorized quotation and received label. The carton is not the deployable asset: each of the ten access points needs its own serial, location, controller and acceptance result.

Q regulatory-domain channel evidence

Cisco's 2800 Series data sheet lists the Q profile as 2.4 GHz channels 1-13; 5 GHz blocks at 5.180-5.320 and 5.500-5.700 GHz. The Q profile provides lower and continuous middle 5 GHz blocks without the upper block listed for some domains. Capacity and interference planning should use those two groups only.

Export the lower and middle channel sets from the target controller and compare them with the Q-domain survey. Escalate an upper-band dependency before the purchase is released. Regulatory-domain letters are identifiers, not country names; use Cisco's compliance tool for the actual deployment country and retain the lookup date.

Procurement inference: the absence of a listed upper block means that lower and middle spectrum must carry the intended design. Before purchase, confirm that survey capacity and neighboring deployments do not depend on upper-band separation. During acceptance, record utilization in both available groups and document any controller policy that further narrows them. A different domain's three-group template is not suitable substitution evidence.

Deployment evidence worksheet

Mechanical installation record

List the bracket, ceiling or wall interface, enclosure requirement, safety restraint, service clearance and cable-entry plan before scheduling installation. Receiving should identify missing mechanical items before the access point reaches site. Photograph the mounted label and final cable entry, then record how the unit can be reached for replacement. A complete electronic order can still be an unusable deployment kit when mechanical dependencies are omitted.

Serial-level asset control

Capture chassis serial, base MAC address, carton reference, deployment site, controller assignment and asset owner. Reconcile the identifiers against the purchase line before activation. Multi-unit cartons require an entry for every physical access point; a carton SKU alone cannot show which unit was installed, held as a spare or returned. This record is also needed to trace support entitlement, replacement history and monitoring ownership.

Software lifecycle file

Record the controller release approved for this unit, the source used to verify support, the last tested date and the owner for software advisories. Available hardware does not prove compatibility with a current or future controller train. Review Cisco support information before every expansion or replacement. The lifecycle file should also state when this Aironet generation must leave service and which surrounding dependencies need migration.

Controlled spare policy

If purchased as a spare, name the protected site population, compatible controller image, storage location, storage conditions and periodic power-on test. Confirm that regulatory token, antenna architecture and mounting parts match the population it protects. Set a final-use review date. A stored unit can become unsuitable while untouched because controller software, country approval, certificates or network architecture may change.

Interference baseline

Preserve the pre-install and post-install noise, neighboring-radio and channel-occupancy observations for the selected location. Record any controller-driven channel change during acceptance. If the regulatory profile limits the channel choices, state how that constraint affected reuse and mitigation. This baseline gives future troubleshooting a reference point and prevents an unrelated interference change from being attributed to the hardware order.

Fault-domain separation

Build the acceptance record so power, wired link, controller join, radio state, authentication and application reachability can be reviewed independently. Preserve timestamps and device identifiers across switch and controller logs. When a test fails, identify the failing boundary before replacing hardware. This avoids classifying a cable, policy or controller problem as an access-point defect and creates evidence that can be reused during support escalation.

Operational log retention

Store the initial controller events, switch-port state, radio assignment, channel list and client test results with a consistent asset identifier. Define how long commissioning evidence is retained and who can retrieve it. A later firmware, controller or RF change should add a new dated observation rather than overwrite the original. The resulting history supports lifecycle decisions and distinguishes a new regression from the accepted baseline.

Handover completeness

The handover package should include exact order identity, destination approval, serial record, controller evidence, switch port, mounting or antenna record, user-path tests and named operational owners. Review the package with the receiving team and list unresolved exceptions. A unit is not operationally accepted when important evidence remains only in installer notes, email attachments or an unowned temporary dashboard.

Related Aironet 2802 order records

• AIR-AP2802I-Q-K9C - compare antenna architecture and regulatory-domain evidence.
• AIR-AP2802I-Q-K9 - compare antenna architecture and regulatory-domain evidence.
• AIR-AP2802I-QK910C - compare antenna architecture and regulatory-domain evidence.

Official evidence: Cisco Aironet 2800 Series data sheet; Cisco 2800 Series getting started guide; Cisco 2800 Series support and lifecycle page; and Cisco wireless compliance tool.