AIR-AP2802I-Q-K9 Cisco Aironet 2800i 5.2 Gbps Data Rates Access Point

AIR-AP2802I-Q-K9 exact order identity

AIR-AP2802I-Q-K9 is a Cisco Aironet 2800 Series controller-based 802.11ac Wave 2 access point order. The exact line combines a 2802I indoor access point with integrated antennas, regulatory-domain token Q, and a single-unit, fixed regulatory-domain order.

Antenna boundary

Cisco documents twelve cross-polarized internal antennas in the 2802I enclosure. No external antenna is selected by this access-point SKU. The RF result therefore depends on enclosure orientation, mounting height, obstructions and the surveyed placement. Receiving should confirm the mounting kit, while commissioning should retain photographs of the final orientation and compare measured coverage with the approved survey.

Order-form boundary

Cisco's ordering convention uses K9 for one access point. This line already carries a regulatory-domain token, so receiving must match the complete part number rather than accepting another domain as an equivalent. Create one asset record for the chassis serial and MAC address. Link that record to the approved destination, controller, switch port, mounting position and compliance lookup before the unit joins production. Because this is a fixed-domain line, a quotation or received label carrying another domain is a different order and requires a fresh approval. The single unit needs one serial-level record, while accessories, controller readiness and destination approval remain separate acceptance items.

Q regulatory-domain channel evidence

Cisco's 2800 Series data sheet lists the Q profile as 2.4 GHz channels 1-13; 5 GHz blocks at 5.180-5.320 and 5.500-5.700 GHz. The Q profile provides lower and continuous middle 5 GHz blocks without the upper block listed for some domains. Capacity and interference planning should use those two groups only.

Export the lower and middle channel sets from the target controller and compare them with the Q-domain survey. Escalate an upper-band dependency before the purchase is released. Regulatory-domain letters are identifiers, not country names; use Cisco's compliance tool for the actual deployment country and retain the lookup date.

Procurement inference: the absence of a listed upper block means that lower and middle spectrum must carry the intended design. Before purchase, confirm that survey capacity and neighboring deployments do not depend on upper-band separation. During acceptance, record utilization in both available groups and document any controller policy that further narrows them. A different domain's three-group template is not suitable substitution evidence.

Deployment evidence worksheet

Controller join evidence

Stage the access point on the controller release intended for production. Retain the controller model, software version, discovery path, authorization method and first successful CAPWAP join. Confirm that configuration download completes and that both radios reach an expected operational state. Remove any temporary staging authorization before handover. This evidence separates an orderable access point from a unit that has actually been proven compatible with the planned controller environment.

Ethernet and cabling proof

Preserve the permanent-link test, patch-lead identities, switch port, negotiated Ethernet rate and error counters. Investigate pair faults, excessive length or rate fallback before wireless acceptance begins. A link light only proves connectivity at some rate; it does not demonstrate the intended uplink performance. Tie the cable result to the AP serial so a later throughput problem can be separated from radio, controller and wired-path causes.

Survey-to-install reconciliation

Attach the approved RF survey location, mounting height, orientation, expected client density, channel width and neighboring-radio assumptions to the order. After installation, compare measured coverage and interference with that design. If ceiling construction, antenna placement or obstructions changed, document the deviation and repeat the affected measurements. This provides a site-specific acceptance reason for the exact unit instead of relying on a family data sheet alone.

Country approval retention

Save the Cisco compliance lookup result, lookup date, deployment country, approved regulatory token and reviewer. If the destination changes, stop and repeat the approval rather than moving the unit on the strength of an earlier purchase. Compare the controller country setting and available channels with the retained evidence. Regulatory eligibility is a deployment condition and cannot be inferred from connector fit, stock location or a similar-looking part number.

Software lifecycle file

Record the controller release approved for this unit, the source used to verify support, the last tested date and the owner for software advisories. Available hardware does not prove compatibility with a current or future controller train. Review Cisco support information before every expansion or replacement. The lifecycle file should also state when this Aironet generation must leave service and which surrounding dependencies need migration.

Change-window controls

Document staging evidence, production window, installer, rollback owner and measurable success criteria. Preserve the prior controller or AP state needed for recovery. After the change, close temporary credentials, compare authentication, monitoring and RF results with the approved baseline, and record the final decision. The work is not complete merely because the unit powers on or appears in a controller list.

Interference baseline

Preserve the pre-install and post-install noise, neighboring-radio and channel-occupancy observations for the selected location. Record any controller-driven channel change during acceptance. If the regulatory profile limits the channel choices, state how that constraint affected reuse and mitigation. This baseline gives future troubleshooting a reference point and prevents an unrelated interference change from being attributed to the hardware order.

Handover completeness

The handover package should include exact order identity, destination approval, serial record, controller evidence, switch port, mounting or antenna record, user-path tests and named operational owners. Review the package with the receiving team and list unresolved exceptions. A unit is not operationally accepted when important evidence remains only in installer notes, email attachments or an unowned temporary dashboard.

Related Aironet 2802 order records

• AIR-AP2802E-QK910C - compare antenna architecture and regulatory-domain evidence.
• AIR-AP2802E-QK910 - compare antenna architecture and regulatory-domain evidence.
• AIR-AP2802E-Q-K9C - compare antenna architecture and regulatory-domain evidence.

Official evidence: Cisco Aironet 2800 Series data sheet; Cisco 2800 Series getting started guide; Cisco 2800 Series support and lifecycle page; and Cisco wireless compliance tool.