AIR-AP2802E-A-K9 Cisco Aironet 2800e Dual-band 802.11a/g/n/ac AP

AIR-AP2802E-A-K9 exact order identity

AIR-AP2802E-A-K9 is a Cisco Aironet 2800 Series controller-based 802.11ac Wave 2 access point order. The exact line combines a 2802E indoor access point for external antennas, regulatory-domain token A, and a single-unit, fixed regulatory-domain order.

Antenna boundary

Cisco documents four RP-TNC antenna connectors plus a Smart Antenna connector on the 2802E. Antennas are a separate engineered part of the deployment bill of materials. Before release, record each Cisco-supported antenna part number, connector use, gain, pattern, cable type, cable loss, mounting orientation and local approval. A connector fit alone does not establish RF performance or regulatory suitability.

Order-form boundary

Cisco's ordering convention uses K9 for one access point. This line already carries a regulatory-domain token, so receiving must match the complete part number rather than accepting another domain as an equivalent. Create one asset record for the chassis serial and MAC address. Link that record to the approved destination, controller, switch port, mounting position and compliance lookup before the unit joins production. Because this is a fixed-domain line, a quotation or received label carrying another domain is a different order and requires a fresh approval. The single unit needs one serial-level record, while accessories, controller readiness and destination approval remain separate acceptance items.

A regulatory-domain channel evidence

Cisco's 2800 Series data sheet lists the A profile as 2.4 GHz channels 1-11; 5 GHz blocks at 5.180-5.320, 5.500-5.700 excluding 5.600-5.640, and 5.745-5.825 GHz. The A plan combines lower, middle and upper 5 GHz blocks, but the documented gap inside the middle block matters. The RF design and controller template must preserve that exclusion instead of treating the listed span as continuous.

Export the controller channel list after provisioning and compare it with the approved A-domain record. Investigate any channel inside the excluded middle sub-block or any missing approval evidence before service activation. Regulatory-domain letters are identifiers, not country names; use Cisco's compliance tool for the actual deployment country and retain the lookup date.

Procurement inference: this profile is useful only when the destination approval and controller expose the documented lower, split-middle and upper choices. The middle exclusion should appear explicitly in the site worksheet, because a broad frequency-range label can conceal it. When migrating controllers, compare exported enabled-channel lists before and after the move; do not use unchanged SSID service as proof that the regulatory plan remained intact.

Deployment evidence worksheet

Controller join evidence

Stage the access point on the controller release intended for production. Retain the controller model, software version, discovery path, authorization method and first successful CAPWAP join. Confirm that configuration download completes and that both radios reach an expected operational state. Remove any temporary staging authorization before handover. This evidence separates an orderable access point from a unit that has actually been proven compatible with the planned controller environment.

Power-state acceptance

Measure power after the access point has joined its controller and the planned radios and services are active. Record switch model, port, negotiated power level, LLDP result and any reduced-capability warning. An idle boot result is not sufficient evidence for the deployed power budget. If an injector is proposed, verify its supported use and include its exact identity in the maintained bill of materials rather than treating it as an unspecified accessory.

Survey-to-install reconciliation

Attach the approved RF survey location, mounting height, orientation, expected client density, channel width and neighboring-radio assumptions to the order. After installation, compare measured coverage and interference with that design. If ceiling construction, antenna placement or obstructions changed, document the deviation and repeat the affected measurements. This provides a site-specific acceptance reason for the exact unit instead of relying on a family data sheet alone.

Quotation substitution gate

Compare antenna form, regulatory token, configuration suffix, pack quantity and complete Cisco part number on the authorized quotation. Treat any changed token as a substitution that requires a new technical and regulatory review. Procurement should not accept a nearby Aironet 2802 line merely because the family name matches. Preserve the approved line, received label and exception decision so the final asset can be traced to the exact order reviewed here.

Authentication path test

Commission representative clients through association, authentication, address assignment, DNS and application reachability. Preserve the identity policy used, test client type, result and relevant controller logs. An access point that joins its controller has not yet demonstrated the user path. Repeat the test after any controller, certificate or authentication-service change and retain failures separately from RF or switch-port evidence.

Change-window controls

Document staging evidence, production window, installer, rollback owner and measurable success criteria. Preserve the prior controller or AP state needed for recovery. After the change, close temporary credentials, compare authentication, monitoring and RF results with the approved baseline, and record the final decision. The work is not complete merely because the unit powers on or appears in a controller list.

Receiving inspection

At receipt, compare model label, regulatory token, antenna form, quantity, serials and visible condition with the authorized order. Photograph labels before cartons are separated. Quarantine shortages, mixed units, damaged connectors or unapproved substitutions. Do not rely on a distributor description as evidence that the exact Cisco order arrived. Close the inspection only when every physical unit is accounted for.

Handover completeness

The handover package should include exact order identity, destination approval, serial record, controller evidence, switch port, mounting or antenna record, user-path tests and named operational owners. Review the package with the receiving team and list unresolved exceptions. A unit is not operationally accepted when important evidence remains only in installer notes, email attachments or an unowned temporary dashboard.

Related Aironet 2802 order records

• AIR-AP2802I-AK910 - compare antenna architecture and regulatory-domain evidence.
• AIR-AP2802I-A-K9C - compare antenna architecture and regulatory-domain evidence.
• AIR-AP2802I-A-K9 - compare antenna architecture and regulatory-domain evidence.

Official evidence: Cisco Aironet 2800 Series data sheet; Cisco 2800 Series getting started guide; Cisco 2800 Series support and lifecycle page; and Cisco wireless compliance tool.