AIR-AP2802I-Q-K9C Cisco 2800i controller-based 802.11a/g/n/ac AP

AIR-AP2802I-Q-K9C exact order identity

AIR-AP2802I-Q-K9C is a Cisco Aironet 2800 Series controller-based 802.11ac Wave 2 access point order. The exact line combines a 2802I indoor access point with integrated antennas, regulatory-domain token Q, and a single-unit, configurable order.

Antenna boundary

Cisco documents twelve cross-polarized internal antennas in the 2802I enclosure. No external antenna is selected by this access-point SKU. The RF result therefore depends on enclosure orientation, mounting height, obstructions and the surveyed placement. Receiving should confirm the mounting kit, while commissioning should retain photographs of the final orientation and compare measured coverage with the approved survey.

Order-form boundary

Cisco's ordering convention uses K9C for a configurable single unit. The C suffix does not make the access point globally deployable; the final configured domain and destination approval must still be present on the quotation and received label. Hold the unit at receiving if the configured domain is absent or differs from the approved order. Preserve the configuration selection, chassis serial, destination evidence and controller-domain check as one release record. Because this is a configurable line, purchasing must retain the finally selected domain on both the authorized quotation and received label. The single unit needs one serial-level record, while accessories, controller readiness and destination approval remain separate acceptance items.

Q regulatory-domain channel evidence

Cisco's 2800 Series data sheet lists the Q profile as 2.4 GHz channels 1-13; 5 GHz blocks at 5.180-5.320 and 5.500-5.700 GHz. The Q profile provides lower and continuous middle 5 GHz blocks without the upper block listed for some domains. Capacity and interference planning should use those two groups only.

Export the lower and middle channel sets from the target controller and compare them with the Q-domain survey. Escalate an upper-band dependency before the purchase is released. Regulatory-domain letters are identifiers, not country names; use Cisco's compliance tool for the actual deployment country and retain the lookup date.

Procurement inference: the absence of a listed upper block means that lower and middle spectrum must carry the intended design. Before purchase, confirm that survey capacity and neighboring deployments do not depend on upper-band separation. During acceptance, record utilization in both available groups and document any controller policy that further narrows them. A different domain's three-group template is not suitable substitution evidence.

Deployment evidence worksheet

Ethernet and cabling proof

Preserve the permanent-link test, patch-lead identities, switch port, negotiated Ethernet rate and error counters. Investigate pair faults, excessive length or rate fallback before wireless acceptance begins. A link light only proves connectivity at some rate; it does not demonstrate the intended uplink performance. Tie the cable result to the AP serial so a later throughput problem can be separated from radio, controller and wired-path causes.

Country approval retention

Save the Cisco compliance lookup result, lookup date, deployment country, approved regulatory token and reviewer. If the destination changes, stop and repeat the approval rather than moving the unit on the strength of an earlier purchase. Compare the controller country setting and available channels with the retained evidence. Regulatory eligibility is a deployment condition and cannot be inferred from connector fit, stock location or a similar-looking part number.

Authentication path test

Commission representative clients through association, authentication, address assignment, DNS and application reachability. Preserve the identity policy used, test client type, result and relevant controller logs. An access point that joins its controller has not yet demonstrated the user path. Repeat the test after any controller, certificate or authentication-service change and retain failures separately from RF or switch-port evidence.

Capacity observation

Define the expected concurrent clients, application mix, airtime utilization and channel-width assumptions for this location. After commissioning, capture radio utilization, retry behavior and representative throughput during a meaningful load period. Compare the observation with the survey design and state any shortfall. A peak link rate from a data sheet is not a site capacity result and should not replace measured operating evidence.

Replacement dependency map

Map this unit to controller, licenses, authentication services, switch power, cable, bracket, antenna design and monitoring objects. For an end-of-sale platform, state which dependencies can be reused by the planned Catalyst migration and which require change. A nominal access-point replacement can fail when the surrounding platform was never inventoried. Keep the map with the asset rather than only in a one-time project file.

Receiving inspection

At receipt, compare model label, regulatory token, antenna form, quantity, serials and visible condition with the authorized order. Photograph labels before cartons are separated. Quarantine shortages, mixed units, damaged connectors or unapproved substitutions. Do not rely on a distributor description as evidence that the exact Cisco order arrived. Close the inspection only when every physical unit is accounted for.

Fault-domain separation

Build the acceptance record so power, wired link, controller join, radio state, authentication and application reachability can be reviewed independently. Preserve timestamps and device identifiers across switch and controller logs. When a test fails, identify the failing boundary before replacing hardware. This avoids classifying a cable, policy or controller problem as an access-point defect and creates evidence that can be reused during support escalation.

Operational log retention

Store the initial controller events, switch-port state, radio assignment, channel list and client test results with a consistent asset identifier. Define how long commissioning evidence is retained and who can retrieve it. A later firmware, controller or RF change should add a new dated observation rather than overwrite the original. The resulting history supports lifecycle decisions and distinguishes a new regression from the accepted baseline.

Related Aironet 2802 order records

• AIR-AP2802E-QK910C - compare antenna architecture and regulatory-domain evidence.
• AIR-AP2802E-QK910 - compare antenna architecture and regulatory-domain evidence.
• AIR-AP2802E-Q-K9 - compare antenna architecture and regulatory-domain evidence.

Official evidence: Cisco Aironet 2800 Series data sheet; Cisco 2800 Series getting started guide; Cisco 2800 Series support and lifecycle page; and Cisco wireless compliance tool.