AIR-AP2802E-AK910C Cisco Aironet 2800e Enterprise 5.2 Gbps 10 APs

AIR-AP2802E-AK910C exact order identity

AIR-AP2802E-AK910C is a Cisco Aironet 2800 Series controller-based 802.11ac Wave 2 access point order. The exact line combines a 2802E indoor access point for external antennas, regulatory-domain token A, and a configurable ten-unit eco-pack.

Antenna boundary

Cisco documents four RP-TNC antenna connectors plus a Smart Antenna connector on the 2802E. Antennas are a separate engineered part of the deployment bill of materials. Before release, record each Cisco-supported antenna part number, connector use, gain, pattern, cable type, cable loss, mounting orientation and local approval. A connector fit alone does not establish RF performance or regulatory suitability.

Order-form boundary

Cisco's ordering convention uses K910C for a configurable ten-access-point eco-pack. Configuration selection and physical quantity are separate acceptance gates: the chosen domain must be approved and ten individual units must be reconciled. Retain the configured-domain evidence with the carton record, then create ten serial-level asset rows. Do not release a partial, mixed-domain or unconfigured carton to installation without a documented correction. Because this is a configurable line, purchasing must retain the finally selected domain on both the authorized quotation and received label. The carton is not the deployable asset: each of the ten access points needs its own serial, location, controller and acceptance result.

A regulatory-domain channel evidence

Cisco's 2800 Series data sheet lists the A profile as 2.4 GHz channels 1-11; 5 GHz blocks at 5.180-5.320, 5.500-5.700 excluding 5.600-5.640, and 5.745-5.825 GHz. The A plan combines lower, middle and upper 5 GHz blocks, but the documented gap inside the middle block matters. The RF design and controller template must preserve that exclusion instead of treating the listed span as continuous.

Export the controller channel list after provisioning and compare it with the approved A-domain record. Investigate any channel inside the excluded middle sub-block or any missing approval evidence before service activation. Regulatory-domain letters are identifiers, not country names; use Cisco's compliance tool for the actual deployment country and retain the lookup date.

Procurement inference: this profile is useful only when the destination approval and controller expose the documented lower, split-middle and upper choices. The middle exclusion should appear explicitly in the site worksheet, because a broad frequency-range label can conceal it. When migrating controllers, compare exported enabled-channel lists before and after the move; do not use unchanged SSID service as proof that the regulatory plan remained intact.

Deployment evidence worksheet

Controller join evidence

Stage the access point on the controller release intended for production. Retain the controller model, software version, discovery path, authorization method and first successful CAPWAP join. Confirm that configuration download completes and that both radios reach an expected operational state. Remove any temporary staging authorization before handover. This evidence separates an orderable access point from a unit that has actually been proven compatible with the planned controller environment.

Survey-to-install reconciliation

Attach the approved RF survey location, mounting height, orientation, expected client density, channel width and neighboring-radio assumptions to the order. After installation, compare measured coverage and interference with that design. If ceiling construction, antenna placement or obstructions changed, document the deviation and repeat the affected measurements. This provides a site-specific acceptance reason for the exact unit instead of relying on a family data sheet alone.

Controlled spare policy

If purchased as a spare, name the protected site population, compatible controller image, storage location, storage conditions and periodic power-on test. Confirm that regulatory token, antenna architecture and mounting parts match the population it protects. Set a final-use review date. A stored unit can become unsuitable while untouched because controller software, country approval, certificates or network architecture may change.

Roaming acceptance

Define the neighboring access points and client types used for roaming validation. Record handoff behavior, interruption observed, authentication result and controller events along the intended movement path. Compare the outcome with the site's design target rather than declaring success from static association. Where this unit replaces an older AP, test both entry and exit from its cell so a local improvement does not hide a boundary problem.

Change-window controls

Document staging evidence, production window, installer, rollback owner and measurable success criteria. Preserve the prior controller or AP state needed for recovery. After the change, close temporary credentials, compare authentication, monitoring and RF results with the approved baseline, and record the final decision. The work is not complete merely because the unit powers on or appears in a controller list.

Capacity observation

Define the expected concurrent clients, application mix, airtime utilization and channel-width assumptions for this location. After commissioning, capture radio utilization, retry behavior and representative throughput during a meaningful load period. Compare the observation with the survey design and state any shortfall. A peak link rate from a data sheet is not a site capacity result and should not replace measured operating evidence.

Interference baseline

Preserve the pre-install and post-install noise, neighboring-radio and channel-occupancy observations for the selected location. Record any controller-driven channel change during acceptance. If the regulatory profile limits the channel choices, state how that constraint affected reuse and mitigation. This baseline gives future troubleshooting a reference point and prevents an unrelated interference change from being attributed to the hardware order.

Receiving inspection

At receipt, compare model label, regulatory token, antenna form, quantity, serials and visible condition with the authorized order. Photograph labels before cartons are separated. Quarantine shortages, mixed units, damaged connectors or unapproved substitutions. Do not rely on a distributor description as evidence that the exact Cisco order arrived. Close the inspection only when every physical unit is accounted for.

Related Aironet 2802 order records

• AIR-AP2802I-AK910 - compare antenna architecture and regulatory-domain evidence.
• AIR-AP2802I-A-K9C - compare antenna architecture and regulatory-domain evidence.
• AIR-AP2802I-A-K9 - compare antenna architecture and regulatory-domain evidence.

Official evidence: Cisco Aironet 2800 Series data sheet; Cisco 2800 Series getting started guide; Cisco 2800 Series support and lifecycle page; and Cisco wireless compliance tool.