AIR-AP2802E-Q-K9C Cisco Aironet 2800e Dual-band 2.4/5GHz Access Point

AIR-AP2802E-Q-K9C exact order identity

AIR-AP2802E-Q-K9C is a Cisco Aironet 2800 Series controller-based 802.11ac Wave 2 access point order. The exact line combines a 2802E indoor access point for external antennas, regulatory-domain token Q, and a single-unit, configurable order.

Antenna boundary

Cisco documents four RP-TNC antenna connectors plus a Smart Antenna connector on the 2802E. Antennas are a separate engineered part of the deployment bill of materials. Before release, record each Cisco-supported antenna part number, connector use, gain, pattern, cable type, cable loss, mounting orientation and local approval. A connector fit alone does not establish RF performance or regulatory suitability.

Order-form boundary

Cisco's ordering convention uses K9C for a configurable single unit. The C suffix does not make the access point globally deployable; the final configured domain and destination approval must still be present on the quotation and received label. Hold the unit at receiving if the configured domain is absent or differs from the approved order. Preserve the configuration selection, chassis serial, destination evidence and controller-domain check as one release record. Because this is a configurable line, purchasing must retain the finally selected domain on both the authorized quotation and received label. The single unit needs one serial-level record, while accessories, controller readiness and destination approval remain separate acceptance items.

Q regulatory-domain channel evidence

Cisco's 2800 Series data sheet lists the Q profile as 2.4 GHz channels 1-13; 5 GHz blocks at 5.180-5.320 and 5.500-5.700 GHz. The Q profile provides lower and continuous middle 5 GHz blocks without the upper block listed for some domains. Capacity and interference planning should use those two groups only.

Export the lower and middle channel sets from the target controller and compare them with the Q-domain survey. Escalate an upper-band dependency before the purchase is released. Regulatory-domain letters are identifiers, not country names; use Cisco's compliance tool for the actual deployment country and retain the lookup date.

Procurement inference: the absence of a listed upper block means that lower and middle spectrum must carry the intended design. Before purchase, confirm that survey capacity and neighboring deployments do not depend on upper-band separation. During acceptance, record utilization in both available groups and document any controller policy that further narrows them. A different domain's three-group template is not suitable substitution evidence.

Deployment evidence worksheet

Controller join evidence

Stage the access point on the controller release intended for production. Retain the controller model, software version, discovery path, authorization method and first successful CAPWAP join. Confirm that configuration download completes and that both radios reach an expected operational state. Remove any temporary staging authorization before handover. This evidence separates an orderable access point from a unit that has actually been proven compatible with the planned controller environment.

Power-state acceptance

Measure power after the access point has joined its controller and the planned radios and services are active. Record switch model, port, negotiated power level, LLDP result and any reduced-capability warning. An idle boot result is not sufficient evidence for the deployed power budget. If an injector is proposed, verify its supported use and include its exact identity in the maintained bill of materials rather than treating it as an unspecified accessory.

Ethernet and cabling proof

Preserve the permanent-link test, patch-lead identities, switch port, negotiated Ethernet rate and error counters. Investigate pair faults, excessive length or rate fallback before wireless acceptance begins. A link light only proves connectivity at some rate; it does not demonstrate the intended uplink performance. Tie the cable result to the AP serial so a later throughput problem can be separated from radio, controller and wired-path causes.

Survey-to-install reconciliation

Attach the approved RF survey location, mounting height, orientation, expected client density, channel width and neighboring-radio assumptions to the order. After installation, compare measured coverage and interference with that design. If ceiling construction, antenna placement or obstructions changed, document the deviation and repeat the affected measurements. This provides a site-specific acceptance reason for the exact unit instead of relying on a family data sheet alone.

Monitoring handover

Assign owners for AP reachability, controller join failures, radio utilization, client health and switch-port errors. Confirm that the exact serial appears in inventory and monitoring, then test the alert path. Record dashboard object, notification route and escalation owner. Telemetry that is not tied to an owned asset does not provide a reliable service baseline and will not support later comparison after channel or software changes.

Change-window controls

Document staging evidence, production window, installer, rollback owner and measurable success criteria. Preserve the prior controller or AP state needed for recovery. After the change, close temporary credentials, compare authentication, monitoring and RF results with the approved baseline, and record the final decision. The work is not complete merely because the unit powers on or appears in a controller list.

Security baseline

Retain the approved controller policy, management authorization, certificate or trust workflow, client authentication test and logging destination. Confirm behavior on the deployed controller software instead of promising a protocol from the hardware family name. Remove temporary onboarding access and verify administrative reachability after handover. This keeps product identity separate from software-dependent security claims.

Capacity observation

Define the expected concurrent clients, application mix, airtime utilization and channel-width assumptions for this location. After commissioning, capture radio utilization, retry behavior and representative throughput during a meaningful load period. Compare the observation with the survey design and state any shortfall. A peak link rate from a data sheet is not a site capacity result and should not replace measured operating evidence.

Related Aironet 2802 order records

• AIR-AP2802I-QK910C - compare antenna architecture and regulatory-domain evidence.
• AIR-AP2802I-Q-K9 - compare antenna architecture and regulatory-domain evidence.
• AIR-AP2802I-Q-K9C - compare antenna architecture and regulatory-domain evidence.

Official evidence: Cisco Aironet 2800 Series data sheet; Cisco 2800 Series getting started guide; Cisco 2800 Series support and lifecycle page; and Cisco wireless compliance tool.