AIRAP1832I-QK910C Cisco 1832i Bluetooth 4 3x3 MIMO Mobility Express AP

AIRAP1832I-QK910C exact order identity

AIRAP1832I-QK910C is a Cisco Aironet 1832i indoor access point with integrated antennas. This exact PID combines regulatory-domain token Q with a legacy K910C Mobility Express procurement line. Cisco documents 802.11ac Wave 2, 3x3 MIMO with two spatial streams and a maximum 5-GHz PHY rate of 867 Mbps.

Integrated-antenna boundary

The 1832i antenna system is internal. No external antenna is selected by this access-point PID, so mounting location, orientation, ceiling construction and the post-install survey determine how the published platform is used.

Software and order boundary

Cisco's Aironet 1830 lifecycle bulletin lists each AIRAP1832I-xK910C PID as Cisco Aironet Mobility Express 1830 Series. The bulletin does not state the physical carton quantity for these K910C lines. Verify quantity, serial count and software role from the authorized quotation and received carton rather than expanding the suffix into an unsupported claim.

Q regulatory-domain evidence

Cisco treats the letter as a regulatory-domain identifier and requires approval for the country of use; it is not a country name. Store the Q-domain compliance result with serial, site and antenna form so return or replacement activity remains traceable.

Organize the Q-domain evidence for return and replacement traceability. Preserve the original unit's PID, approval and site, then require the replacement label and controller country to be checked independently. Link both serials to the same service case without copying the old approval blindly. This makes regulatory identity visible during an RMA rather than only during initial purchase.

Power and interface boundary

The AP supports 802.3af, 802.3at, Enhanced PoE, a local power supply and Cisco power injectors. Cisco lists a 15.4 W draw and states that USB is disabled when 802.3af is used. Record the negotiated power and the single Gigabit Ethernet uplink state.

Lifecycle decision

Cisco ended sale of the Aironet 1830 Series on 1 May 2022, ended software maintenance on 1 May 2023 and lists 30 April 2027 as the last support date. Cisco identifies Catalyst 9115AX as the migration family; available inventory does not extend these dates.

Deployment evidence worksheet

Power-state acceptance

Measure power after the access point has joined its controller and the planned radios and services are active. Record switch model, port, negotiated power level, LLDP result and any reduced-capability warning. An idle boot result is not sufficient evidence for the deployed power budget. If an injector is proposed, verify its supported use and include its exact identity in the maintained bill of materials rather than treating it as an unspecified accessory. The 1832i draws up to 15.4 W and supports 802.3af or 802.3at; Cisco states that 802.3af disables the USB port.

Serial-level asset control

Capture chassis serial, base MAC address, carton reference, deployment site, controller assignment and asset owner. Reconcile the identifiers against the purchase line before activation. Multi-unit cartons require an entry for every physical access point; a carton SKU alone cannot show which unit was installed, held as a spare or returned. This record is also needed to trace support entitlement, replacement history and monitoring ownership. For a K910C line, reconcile every received serial against the authorized carton quantity because Cisco's lifecycle description does not state that quantity.

Controlled spare policy

If purchased as a spare, name the protected site population, compatible controller image, storage location, storage conditions and periodic power-on test. Confirm that regulatory token, antenna architecture and mounting parts match the population it protects. Set a final-use review date. A stored unit can become unsuitable while untouched because controller software, country approval, certificates or network architecture may change. A spare 1832i should be tested against the protected controller release, domain, mounting hardware and April 2027 support cutoff.

Authentication path test

Commission representative clients through association, authentication, address assignment, DNS and application reachability. Preserve the identity policy used, test client type, result and relevant controller logs. An access point that joins its controller has not yet demonstrated the user path. Repeat the test after any controller, certificate or authentication-service change and retain failures separately from RF or switch-port evidence. Test association, authentication, DHCP, DNS and application reachability after the AP reaches its final controller or Mobility Express role.

Change-window controls

Document staging evidence, production window, installer, rollback owner and measurable success criteria. Preserve the prior controller or AP state needed for recovery. After the change, close temporary credentials, compare authentication, monitoring and RF results with the approved baseline, and record the final decision. The work is not complete merely because the unit powers on or appears in a controller list. Rollback must restore the former controller or Mobility Express role, country setting, switch port and accepted RF state.

Security baseline

Retain the approved controller policy, management authorization, certificate or trust workflow, client authentication test and logging destination. Confirm behavior on the deployed controller software instead of promising a protocol from the hardware family name. Remove temporary onboarding access and verify administrative reachability after handover. This keeps product identity separate from software-dependent security claims. Record which security functions are actually configured on the deployed controller release; do not present optional family capabilities as enabled facts.

Receiving inspection

At receipt, compare model label, regulatory token, antenna form, quantity, serials and visible condition with the authorized order. Photograph labels before cartons are separated. Quarantine shortages, mixed units, damaged connectors or unapproved substitutions. Do not rely on a distributor description as evidence that the exact Cisco order arrived. Close the inspection only when every physical unit is accounted for. Receiving should verify the integrated-antenna 1832i identity and distinguish K9, K9C and K910C software or procurement forms.

Fault-domain separation

Build the acceptance record so power, wired link, controller join, radio state, authentication and application reachability can be reviewed independently. Preserve timestamps and device identifiers across switch and controller logs. When a test fails, identify the failing boundary before replacing hardware. This avoids classifying a cable, policy or controller problem as an access-point defect and creates evidence that can be reused during support escalation. Use controller, switch and client timestamps to separate power, CAPWAP, RF and authentication faults before declaring hardware failure.

Related Aironet 1832 order records

• AIR-AP1832I-Z-K9C - compare regulatory-domain evidence.
• AIR-AP1832I-Z-K9 - compare regulatory-domain evidence.
• AIR-AP1832I-T-K9C - compare regulatory-domain evidence.

Official evidence: Cisco Aironet 1830 Series data sheet; Cisco Aironet 1830 lifecycle bulletin; Cisco Aironet 1830 support page; and Cisco wireless compliance tool.