CISCO AIRAP1832I-ZK910C Aironet 1832i Access Points

AIRAP1832I-ZK910C exact order identity

AIRAP1832I-ZK910C is a Cisco Aironet 1832i indoor access point with integrated antennas. This exact PID combines regulatory-domain token Z with a legacy K910C Mobility Express procurement line. Cisco documents 802.11ac Wave 2, 3x3 MIMO with two spatial streams and a maximum 5-GHz PHY rate of 867 Mbps.

Integrated-antenna boundary

The 1832i antenna system is internal. No external antenna is selected by this access-point PID, so mounting location, orientation, ceiling construction and the post-install survey determine how the published platform is used.

Software and order boundary

Cisco's Aironet 1830 lifecycle bulletin lists each AIRAP1832I-xK910C PID as Cisco Aironet Mobility Express 1830 Series. The bulletin does not state the physical carton quantity for these K910C lines. Verify quantity, serial count and software role from the authorized quotation and received carton rather than expanding the suffix into an unsupported claim.

Z regulatory-domain evidence

Cisco treats the letter as a regulatory-domain identifier and requires approval for the country of use; it is not a country name. Attach the Z-domain compliance lookup to the commissioning package and flag any later country-setting change for reapproval.

Build the Z-domain package as a commissioning baseline. Combine the exact PID, destination lookup, controller country, enabled-channel output, antenna or mounting evidence and representative client test under one review date. Later automatic radio changes may be operationally valid, but country-setting or hardware reassignment changes require explicit reapproval and a new baseline entry.

Power and interface boundary

The AP supports 802.3af, 802.3at, Enhanced PoE, a local power supply and Cisco power injectors. Cisco lists a 15.4 W draw and states that USB is disabled when 802.3af is used. Record the negotiated power and the single Gigabit Ethernet uplink state.

Lifecycle decision

Cisco ended sale of the Aironet 1830 Series on 1 May 2022, ended software maintenance on 1 May 2023 and lists 30 April 2027 as the last support date. Cisco identifies Catalyst 9115AX as the migration family; available inventory does not extend these dates.

Deployment evidence worksheet

Controller join evidence

Stage the access point on the controller release intended for production. Retain the controller model, software version, discovery path, authorization method and first successful CAPWAP join. Confirm that configuration download completes and that both radios reach an expected operational state. Remove any temporary staging authorization before handover. This evidence separates an orderable access point from a unit that has actually been proven compatible with the planned controller environment. For the 1832i, retain the controller or Mobility Express role, software release, regulatory token and first successful join.

Power-state acceptance

Measure power after the access point has joined its controller and the planned radios and services are active. Record switch model, port, negotiated power level, LLDP result and any reduced-capability warning. An idle boot result is not sufficient evidence for the deployed power budget. If an injector is proposed, verify its supported use and include its exact identity in the maintained bill of materials rather than treating it as an unspecified accessory. The 1832i draws up to 15.4 W and supports 802.3af or 802.3at; Cisco states that 802.3af disables the USB port.

Ethernet and cabling proof

Preserve the permanent-link test, patch-lead identities, switch port, negotiated Ethernet rate and error counters. Investigate pair faults, excessive length or rate fallback before wireless acceptance begins. A link light only proves connectivity at some rate; it does not demonstrate the intended uplink performance. Tie the cable result to the AP serial so a later throughput problem can be separated from radio, controller and wired-path causes. Record the single 10/100/1000 Ethernet uplink rate, cable test and switch-port counters before evaluating wireless performance.

Survey-to-install reconciliation

Attach the approved RF survey location, mounting height, orientation, expected client density, channel width and neighboring-radio assumptions to the order. After installation, compare measured coverage and interference with that design. If ceiling construction, antenna placement or obstructions changed, document the deviation and repeat the affected measurements. This provides a site-specific acceptance reason for the exact unit instead of relying on a family data sheet alone. Compare the installed integrated-antenna orientation and measured coverage with the approved survey instead of relying on the family data sheet.

Mechanical installation record

List the bracket, ceiling or wall interface, enclosure requirement, safety restraint, service clearance and cable-entry plan before scheduling installation. Receiving should identify missing mechanical items before the access point reaches site. Photograph the mounted label and final cable entry, then record how the unit can be reached for replacement. A complete electronic order can still be an unusable deployment kit when mechanical dependencies are omitted. The 1832i supports common Cisco Aironet mounting brackets; preserve the exact bracket and ceiling or wall interface used at the site.

Serial-level asset control

Capture chassis serial, base MAC address, carton reference, deployment site, controller assignment and asset owner. Reconcile the identifiers against the purchase line before activation. Multi-unit cartons require an entry for every physical access point; a carton SKU alone cannot show which unit was installed, held as a spare or returned. This record is also needed to trace support entitlement, replacement history and monitoring ownership. For a K910C line, reconcile every received serial against the authorized carton quantity because Cisco's lifecycle description does not state that quantity.

Country approval retention

Save the Cisco compliance lookup result, lookup date, deployment country, approved regulatory token and reviewer. If the destination changes, stop and repeat the approval rather than moving the unit on the strength of an earlier purchase. Compare the controller country setting and available channels with the retained evidence. Regulatory eligibility is a deployment condition and cannot be inferred from connector fit, stock location or a similar-looking part number. Cisco makes the customer responsible for country approval; keep the dated compliance lookup with the 1832i serial and controller country.

Quotation substitution gate

Compare antenna form, regulatory token, configuration suffix, pack quantity and complete Cisco part number on the authorized quotation. Treat any changed token as a substitution that requires a new technical and regulatory review. Procurement should not accept a nearby Aironet 2802 line merely because the family name matches. Preserve the approved line, received label and exception decision so the final asset can be traced to the exact order reviewed here. A K9, K9C, K910C or regulatory-token change is a different 1832i procurement line and requires a new review.

Related Aironet 1832 order records

• AIR-AP1832I-Z-K9C - compare software and procurement form.
• AIR-AP1832I-Z-K9 - compare software and procurement form.
• AIR-AP1832I-T-K9C - compare regulatory-domain evidence.

Official evidence: Cisco Aironet 1830 Series data sheet; Cisco Aironet 1830 lifecycle bulletin; Cisco Aironet 1830 support page; and Cisco wireless compliance tool.