AIRAP1832I-CK910C Cisco Aironet 1832i 3x3 MIMO Mobility Express AP

AIRAP1832I-CK910C exact order identity

AIRAP1832I-CK910C is a Cisco Aironet 1832i indoor access point with integrated antennas. This exact PID combines regulatory-domain token C with a legacy K910C Mobility Express procurement line. Cisco documents 802.11ac Wave 2, 3x3 MIMO with two spatial streams and a maximum 5-GHz PHY rate of 867 Mbps.

Integrated-antenna boundary

The 1832i antenna system is internal. No external antenna is selected by this access-point PID, so mounting location, orientation, ceiling construction and the post-install survey determine how the published platform is used.

Software and order boundary

Cisco's Aironet 1830 lifecycle bulletin lists each AIRAP1832I-xK910C PID as Cisco Aironet Mobility Express 1830 Series. The bulletin does not state the physical carton quantity for these K910C lines. Verify quantity, serial count and software role from the authorized quotation and received carton rather than expanding the suffix into an unsupported claim.

C regulatory-domain evidence

Cisco treats the letter as a regulatory-domain identifier and requires approval for the country of use; it is not a country name. Preserve the C-domain destination approval with the exact PID, serial and controller country so a nearby domain cannot be substituted silently.

Use final receiving approval as the C-domain checkpoint. Match the authorized quotation, carton label, chassis serial, destination and controller country before release. Preserve the dated Cisco lookup with those fields. A later replacement or site transfer must create a new decision rather than inheriting the old location's approval from the asset record.

Power and interface boundary

The AP supports 802.3af, 802.3at, Enhanced PoE, a local power supply and Cisco power injectors. Cisco lists a 15.4 W draw and states that USB is disabled when 802.3af is used. Record the negotiated power and the single Gigabit Ethernet uplink state.

Lifecycle decision

Cisco ended sale of the Aironet 1830 Series on 1 May 2022, ended software maintenance on 1 May 2023 and lists 30 April 2027 as the last support date. Cisco identifies Catalyst 9115AX as the migration family; available inventory does not extend these dates.

Deployment evidence worksheet

Power-state acceptance

Measure power after the access point has joined its controller and the planned radios and services are active. Record switch model, port, negotiated power level, LLDP result and any reduced-capability warning. An idle boot result is not sufficient evidence for the deployed power budget. If an injector is proposed, verify its supported use and include its exact identity in the maintained bill of materials rather than treating it as an unspecified accessory. The 1832i draws up to 15.4 W and supports 802.3af or 802.3at; Cisco states that 802.3af disables the USB port.

Mechanical installation record

List the bracket, ceiling or wall interface, enclosure requirement, safety restraint, service clearance and cable-entry plan before scheduling installation. Receiving should identify missing mechanical items before the access point reaches site. Photograph the mounted label and final cable entry, then record how the unit can be reached for replacement. A complete electronic order can still be an unusable deployment kit when mechanical dependencies are omitted. The 1832i supports common Cisco Aironet mounting brackets; preserve the exact bracket and ceiling or wall interface used at the site.

Quotation substitution gate

Compare antenna form, regulatory token, configuration suffix, pack quantity and complete Cisco part number on the authorized quotation. Treat any changed token as a substitution that requires a new technical and regulatory review. Procurement should not accept a nearby Aironet 2802 line merely because the family name matches. Preserve the approved line, received label and exception decision so the final asset can be traced to the exact order reviewed here. A K9, K9C, K910C or regulatory-token change is a different 1832i procurement line and requires a new review.

Controlled spare policy

If purchased as a spare, name the protected site population, compatible controller image, storage location, storage conditions and periodic power-on test. Confirm that regulatory token, antenna architecture and mounting parts match the population it protects. Set a final-use review date. A stored unit can become unsuitable while untouched because controller software, country approval, certificates or network architecture may change. A spare 1832i should be tested against the protected controller release, domain, mounting hardware and April 2027 support cutoff.

Authentication path test

Commission representative clients through association, authentication, address assignment, DNS and application reachability. Preserve the identity policy used, test client type, result and relevant controller logs. An access point that joins its controller has not yet demonstrated the user path. Repeat the test after any controller, certificate or authentication-service change and retain failures separately from RF or switch-port evidence. Test association, authentication, DHCP, DNS and application reachability after the AP reaches its final controller or Mobility Express role.

Monitoring handover

Assign owners for AP reachability, controller join failures, radio utilization, client health and switch-port errors. Confirm that the exact serial appears in inventory and monitoring, then test the alert path. Record dashboard object, notification route and escalation owner. Telemetry that is not tied to an owned asset does not provide a reliable service baseline and will not support later comparison after channel or software changes. Monitoring should connect the 1832i serial with join state, radio health, Ethernet errors, client experience and lifecycle ownership.

Capacity observation

Define the expected concurrent clients, application mix, airtime utilization and channel-width assumptions for this location. After commissioning, capture radio utilization, retry behavior and representative throughput during a meaningful load period. Compare the observation with the survey design and state any shortfall. A peak link rate from a data sheet is not a site capacity result and should not replace measured operating evidence. Capacity evidence should use measured airtime, retries, client mix and channel width rather than the published 867-Mbps 5-GHz PHY rate.

Interference baseline

Preserve the pre-install and post-install noise, neighboring-radio and channel-occupancy observations for the selected location. Record any controller-driven channel change during acceptance. If the regulatory profile limits the channel choices, state how that constraint affected reuse and mitigation. This baseline gives future troubleshooting a reference point and prevents an unrelated interference change from being attributed to the hardware order. Preserve the live controller country and enabled-channel state beside the exact domain token and deployment approval.

Related Aironet 1832 order records

• AIR-AP1832I-C-K9C - compare software and procurement form.
• AIR-AP1832I-Z-K9C - compare regulatory-domain evidence.
• AIR-AP1832I-Z-K9 - compare regulatory-domain evidence.

Official evidence: Cisco Aironet 1830 Series data sheet; Cisco Aironet 1830 lifecycle bulletin; Cisco Aironet 1830 support page; and Cisco wireless compliance tool.