AIR-AP2802I-C-K9 Cisco Aironet 2800i 802.11ac Wave 2 Access Point

AIR-AP2802I-C-K9 exact order identity

AIR-AP2802I-C-K9 is a Cisco Aironet 2800 Series controller-based 802.11ac Wave 2 access point order. The exact line combines a 2802I indoor access point with integrated antennas, regulatory-domain token C, and a single-unit, fixed regulatory-domain order.

Antenna boundary

Cisco documents twelve cross-polarized internal antennas in the 2802I enclosure. No external antenna is selected by this access-point SKU. The RF result therefore depends on enclosure orientation, mounting height, obstructions and the surveyed placement. Receiving should confirm the mounting kit, while commissioning should retain photographs of the final orientation and compare measured coverage with the approved survey.

Order-form boundary

Cisco's ordering convention uses K9 for one access point. This line already carries a regulatory-domain token, so receiving must match the complete part number rather than accepting another domain as an equivalent. Create one asset record for the chassis serial and MAC address. Link that record to the approved destination, controller, switch port, mounting position and compliance lookup before the unit joins production. Because this is a fixed-domain line, a quotation or received label carrying another domain is a different order and requires a fresh approval. The single unit needs one serial-level record, while accessories, controller readiness and destination approval remain separate acceptance items.

C regulatory-domain channel evidence

Cisco's 2800 Series data sheet lists the C profile as 2.4 GHz channels 1-13 and the 5.745-5.825 GHz upper block. The C profile listed by Cisco does not include the lower or middle 5 GHz blocks shown for many other domains. That narrower 5 GHz choice can materially change capacity and channel reuse assumptions.

Reject a design copied from a lower-band domain. Commission the site against the upper-block channel set, record the controller country setting and repeat the survey if the original design assumed unavailable 5 GHz channels. Regulatory-domain letters are identifiers, not country names; use Cisco's compliance tool for the actual deployment country and retain the lookup date.

Procurement inference: this is an upper-5-GHz-focused profile in Cisco's table, so the buying decision should be based on a survey that can operate without lower or middle 5 GHz choices. Check client and infrastructure support for the selected operating plan at the actual site. A successful bench join in a different country or controller setting does not validate the channel availability required by the deployment.

Deployment evidence worksheet

Controller join evidence

Stage the access point on the controller release intended for production. Retain the controller model, software version, discovery path, authorization method and first successful CAPWAP join. Confirm that configuration download completes and that both radios reach an expected operational state. Remove any temporary staging authorization before handover. This evidence separates an orderable access point from a unit that has actually been proven compatible with the planned controller environment.

Ethernet and cabling proof

Preserve the permanent-link test, patch-lead identities, switch port, negotiated Ethernet rate and error counters. Investigate pair faults, excessive length or rate fallback before wireless acceptance begins. A link light only proves connectivity at some rate; it does not demonstrate the intended uplink performance. Tie the cable result to the AP serial so a later throughput problem can be separated from radio, controller and wired-path causes.

Mechanical installation record

List the bracket, ceiling or wall interface, enclosure requirement, safety restraint, service clearance and cable-entry plan before scheduling installation. Receiving should identify missing mechanical items before the access point reaches site. Photograph the mounted label and final cable entry, then record how the unit can be reached for replacement. A complete electronic order can still be an unusable deployment kit when mechanical dependencies are omitted.

Country approval retention

Save the Cisco compliance lookup result, lookup date, deployment country, approved regulatory token and reviewer. If the destination changes, stop and repeat the approval rather than moving the unit on the strength of an earlier purchase. Compare the controller country setting and available channels with the retained evidence. Regulatory eligibility is a deployment condition and cannot be inferred from connector fit, stock location or a similar-looking part number.

Software lifecycle file

Record the controller release approved for this unit, the source used to verify support, the last tested date and the owner for software advisories. Available hardware does not prove compatibility with a current or future controller train. Review Cisco support information before every expansion or replacement. The lifecycle file should also state when this Aironet generation must leave service and which surrounding dependencies need migration.

Controlled spare policy

If purchased as a spare, name the protected site population, compatible controller image, storage location, storage conditions and periodic power-on test. Confirm that regulatory token, antenna architecture and mounting parts match the population it protects. Set a final-use review date. A stored unit can become unsuitable while untouched because controller software, country approval, certificates or network architecture may change.

Security baseline

Retain the approved controller policy, management authorization, certificate or trust workflow, client authentication test and logging destination. Confirm behavior on the deployed controller software instead of promising a protocol from the hardware family name. Remove temporary onboarding access and verify administrative reachability after handover. This keeps product identity separate from software-dependent security claims.

Capacity observation

Define the expected concurrent clients, application mix, airtime utilization and channel-width assumptions for this location. After commissioning, capture radio utilization, retry behavior and representative throughput during a meaningful load period. Compare the observation with the survey design and state any shortfall. A peak link rate from a data sheet is not a site capacity result and should not replace measured operating evidence.

Related Aironet 2802 order records

• AIR-AP2802E-CK910C - compare antenna architecture and regulatory-domain evidence.
• AIR-AP2802E-CK910 - compare antenna architecture and regulatory-domain evidence.
• AIR-AP2802E-C-K9C - compare antenna architecture and regulatory-domain evidence.

Official evidence: Cisco Aironet 2800 Series data sheet; Cisco 2800 Series getting started guide; Cisco 2800 Series support and lifecycle page; and Cisco wireless compliance tool.