AIR-AP2802E-DK910C Cisco Aironet 2800e WiFi 5 10-pack APs

AIR-AP2802E-DK910C exact order identity

AIR-AP2802E-DK910C is a Cisco Aironet 2800 Series controller-based 802.11ac Wave 2 access point order. The exact line combines a 2802E indoor access point for external antennas, regulatory-domain token D, and a configurable ten-unit eco-pack.

Antenna boundary

Cisco documents four RP-TNC antenna connectors plus a Smart Antenna connector on the 2802E. Antennas are a separate engineered part of the deployment bill of materials. Before release, record each Cisco-supported antenna part number, connector use, gain, pattern, cable type, cable loss, mounting orientation and local approval. A connector fit alone does not establish RF performance or regulatory suitability.

Order-form boundary

Cisco's ordering convention uses K910C for a configurable ten-access-point eco-pack. Configuration selection and physical quantity are separate acceptance gates: the chosen domain must be approved and ten individual units must be reconciled. Retain the configured-domain evidence with the carton record, then create ten serial-level asset rows. Do not release a partial, mixed-domain or unconfigured carton to installation without a documented correction. Because this is a configurable line, purchasing must retain the finally selected domain on both the authorized quotation and received label. The carton is not the deployable asset: each of the ten access points needs its own serial, location, controller and acceptance result.

D regulatory-domain channel evidence

Cisco's 2800 Series data sheet lists the D profile as 2.4 GHz channels 1-11; 5 GHz blocks at 5.180-5.320 and 5.745-5.825 GHz. The D profile uses separated lower and upper 5 GHz blocks with no documented middle block. A channel plan that assumes a continuous 5 GHz range is therefore not suitable evidence for this order.

Verify that the controller presents the two expected 5 GHz groups and excludes an unapproved middle range. Store the result with the deployment country lookup and the exact D-domain quotation. Regulatory-domain letters are identifiers, not country names; use Cisco's compliance tool for the actual deployment country and retain the lookup date.

Procurement inference: the separation between lower and upper 5 GHz groups should be represented as two planning pools. During acceptance, compare utilization and interference in each pool rather than averaging all 5 GHz observations together. If a replacement AP was previously using a middle-range channel under another profile, document the revised reuse plan before treating the D-domain unit as a direct substitution.

Deployment evidence worksheet

Power-state acceptance

Measure power after the access point has joined its controller and the planned radios and services are active. Record switch model, port, negotiated power level, LLDP result and any reduced-capability warning. An idle boot result is not sufficient evidence for the deployed power budget. If an injector is proposed, verify its supported use and include its exact identity in the maintained bill of materials rather than treating it as an unspecified accessory.

Ethernet and cabling proof

Preserve the permanent-link test, patch-lead identities, switch port, negotiated Ethernet rate and error counters. Investigate pair faults, excessive length or rate fallback before wireless acceptance begins. A link light only proves connectivity at some rate; it does not demonstrate the intended uplink performance. Tie the cable result to the AP serial so a later throughput problem can be separated from radio, controller and wired-path causes.

Controlled spare policy

If purchased as a spare, name the protected site population, compatible controller image, storage location, storage conditions and periodic power-on test. Confirm that regulatory token, antenna architecture and mounting parts match the population it protects. Set a final-use review date. A stored unit can become unsuitable while untouched because controller software, country approval, certificates or network architecture may change.

Roaming acceptance

Define the neighboring access points and client types used for roaming validation. Record handoff behavior, interruption observed, authentication result and controller events along the intended movement path. Compare the outcome with the site's design target rather than declaring success from static association. Where this unit replaces an older AP, test both entry and exit from its cell so a local improvement does not hide a boundary problem.

Monitoring handover

Assign owners for AP reachability, controller join failures, radio utilization, client health and switch-port errors. Confirm that the exact serial appears in inventory and monitoring, then test the alert path. Record dashboard object, notification route and escalation owner. Telemetry that is not tied to an owned asset does not provide a reliable service baseline and will not support later comparison after channel or software changes.

Security baseline

Retain the approved controller policy, management authorization, certificate or trust workflow, client authentication test and logging destination. Confirm behavior on the deployed controller software instead of promising a protocol from the hardware family name. Remove temporary onboarding access and verify administrative reachability after handover. This keeps product identity separate from software-dependent security claims.

Interference baseline

Preserve the pre-install and post-install noise, neighboring-radio and channel-occupancy observations for the selected location. Record any controller-driven channel change during acceptance. If the regulatory profile limits the channel choices, state how that constraint affected reuse and mitigation. This baseline gives future troubleshooting a reference point and prevents an unrelated interference change from being attributed to the hardware order.

Receiving inspection

At receipt, compare model label, regulatory token, antenna form, quantity, serials and visible condition with the authorized order. Photograph labels before cartons are separated. Quarantine shortages, mixed units, damaged connectors or unapproved substitutions. Do not rely on a distributor description as evidence that the exact Cisco order arrived. Close the inspection only when every physical unit is accounted for.

Related Aironet 2802 order records

• AIR-AP2802I-DK910 - compare antenna architecture and regulatory-domain evidence.
• AIR-AP2802I-D-K9C - compare antenna architecture and regulatory-domain evidence.
• AIR-AP2802I-D-K9 - compare antenna architecture and regulatory-domain evidence.

Official evidence: Cisco Aironet 2800 Series data sheet; Cisco 2800 Series getting started guide; Cisco 2800 Series support and lifecycle page; and Cisco wireless compliance tool.