AIR-AP2802I-C-K9C Cisco Aironet 2800i 802.11ac Wave 2 Access Point

AIR-AP2802I-C-K9C exact order identity

AIR-AP2802I-C-K9C is a Cisco Aironet 2800 Series controller-based 802.11ac Wave 2 access point order. The exact line combines a 2802I indoor access point with integrated antennas, regulatory-domain token C, and a single-unit, configurable order.

Antenna boundary

Cisco documents twelve cross-polarized internal antennas in the 2802I enclosure. No external antenna is selected by this access-point SKU. The RF result therefore depends on enclosure orientation, mounting height, obstructions and the surveyed placement. Receiving should confirm the mounting kit, while commissioning should retain photographs of the final orientation and compare measured coverage with the approved survey.

Order-form boundary

Cisco's ordering convention uses K9C for a configurable single unit. The C suffix does not make the access point globally deployable; the final configured domain and destination approval must still be present on the quotation and received label. Hold the unit at receiving if the configured domain is absent or differs from the approved order. Preserve the configuration selection, chassis serial, destination evidence and controller-domain check as one release record. Because this is a configurable line, purchasing must retain the finally selected domain on both the authorized quotation and received label. The single unit needs one serial-level record, while accessories, controller readiness and destination approval remain separate acceptance items.

C regulatory-domain channel evidence

Cisco's 2800 Series data sheet lists the C profile as 2.4 GHz channels 1-13 and the 5.745-5.825 GHz upper block. The C profile listed by Cisco does not include the lower or middle 5 GHz blocks shown for many other domains. That narrower 5 GHz choice can materially change capacity and channel reuse assumptions.

Reject a design copied from a lower-band domain. Commission the site against the upper-block channel set, record the controller country setting and repeat the survey if the original design assumed unavailable 5 GHz channels. Regulatory-domain letters are identifiers, not country names; use Cisco's compliance tool for the actual deployment country and retain the lookup date.

Procurement inference: this is an upper-5-GHz-focused profile in Cisco's table, so the buying decision should be based on a survey that can operate without lower or middle 5 GHz choices. Check client and infrastructure support for the selected operating plan at the actual site. A successful bench join in a different country or controller setting does not validate the channel availability required by the deployment.

Deployment evidence worksheet

Controller join evidence

Stage the access point on the controller release intended for production. Retain the controller model, software version, discovery path, authorization method and first successful CAPWAP join. Confirm that configuration download completes and that both radios reach an expected operational state. Remove any temporary staging authorization before handover. This evidence separates an orderable access point from a unit that has actually been proven compatible with the planned controller environment.

Power-state acceptance

Measure power after the access point has joined its controller and the planned radios and services are active. Record switch model, port, negotiated power level, LLDP result and any reduced-capability warning. An idle boot result is not sufficient evidence for the deployed power budget. If an injector is proposed, verify its supported use and include its exact identity in the maintained bill of materials rather than treating it as an unspecified accessory.

Mechanical installation record

List the bracket, ceiling or wall interface, enclosure requirement, safety restraint, service clearance and cable-entry plan before scheduling installation. Receiving should identify missing mechanical items before the access point reaches site. Photograph the mounted label and final cable entry, then record how the unit can be reached for replacement. A complete electronic order can still be an unusable deployment kit when mechanical dependencies are omitted.

Country approval retention

Save the Cisco compliance lookup result, lookup date, deployment country, approved regulatory token and reviewer. If the destination changes, stop and repeat the approval rather than moving the unit on the strength of an earlier purchase. Compare the controller country setting and available channels with the retained evidence. Regulatory eligibility is a deployment condition and cannot be inferred from connector fit, stock location or a similar-looking part number.

Software lifecycle file

Record the controller release approved for this unit, the source used to verify support, the last tested date and the owner for software advisories. Available hardware does not prove compatibility with a current or future controller train. Review Cisco support information before every expansion or replacement. The lifecycle file should also state when this Aironet generation must leave service and which surrounding dependencies need migration.

Authentication path test

Commission representative clients through association, authentication, address assignment, DNS and application reachability. Preserve the identity policy used, test client type, result and relevant controller logs. An access point that joins its controller has not yet demonstrated the user path. Repeat the test after any controller, certificate or authentication-service change and retain failures separately from RF or switch-port evidence.

Replacement dependency map

Map this unit to controller, licenses, authentication services, switch power, cable, bracket, antenna design and monitoring objects. For an end-of-sale platform, state which dependencies can be reused by the planned Catalyst migration and which require change. A nominal access-point replacement can fail when the surrounding platform was never inventoried. Keep the map with the asset rather than only in a one-time project file.

Receiving inspection

At receipt, compare model label, regulatory token, antenna form, quantity, serials and visible condition with the authorized order. Photograph labels before cartons are separated. Quarantine shortages, mixed units, damaged connectors or unapproved substitutions. Do not rely on a distributor description as evidence that the exact Cisco order arrived. Close the inspection only when every physical unit is accounted for.

Related Aironet 2802 order records

• AIR-AP2802E-CK910C - compare antenna architecture and regulatory-domain evidence.
• AIR-AP2802E-CK910 - compare antenna architecture and regulatory-domain evidence.
• AIR-AP2802E-C-K9C - compare antenna architecture and regulatory-domain evidence.

Official evidence: Cisco Aironet 2800 Series data sheet; Cisco 2800 Series getting started guide; Cisco 2800 Series support and lifecycle page; and Cisco wireless compliance tool.