AIR-AP2802E-ZK910C Cisco Aironet 2800e 4x4:3 MU-MIMO 2.4/5 GHz 10 APs

AIR-AP2802E-ZK910C exact order identity

AIR-AP2802E-ZK910C is a Cisco Aironet 2800 Series controller-based 802.11ac Wave 2 access point order. The exact line combines a 2802E indoor access point for external antennas, regulatory-domain token Z, and a configurable ten-unit eco-pack.

Antenna boundary

Cisco documents four RP-TNC antenna connectors plus a Smart Antenna connector on the 2802E. Antennas are a separate engineered part of the deployment bill of materials. Before release, record each Cisco-supported antenna part number, connector use, gain, pattern, cable type, cable loss, mounting orientation and local approval. A connector fit alone does not establish RF performance or regulatory suitability.

Order-form boundary

Cisco's ordering convention uses K910C for a configurable ten-access-point eco-pack. Configuration selection and physical quantity are separate acceptance gates: the chosen domain must be approved and ten individual units must be reconciled. Retain the configured-domain evidence with the carton record, then create ten serial-level asset rows. Do not release a partial, mixed-domain or unconfigured carton to installation without a documented correction. Because this is a configurable line, purchasing must retain the finally selected domain on both the authorized quotation and received label. The carton is not the deployable asset: each of the ten access points needs its own serial, location, controller and acceptance result.

Z regulatory-domain channel evidence

Cisco's 2800 Series data sheet lists the Z profile as 2.4 GHz channels 1-11; 5 GHz blocks at 5.180-5.320, 5.500-5.700 excluding 5.600-5.640, and 5.745-5.825 GHz. The Z profile spans lower, middle and upper 5 GHz groups while retaining a documented gap in the middle group. That exclusion must survive controller template changes.

Compare the live channel list with the Z-domain evidence after every initial join or controller migration. Treat an enabled channel inside the excluded range as a release blocker. Regulatory-domain letters are identifiers, not country names; use Cisco's compliance tool for the actual deployment country and retain the lookup date.

Procurement inference: lower, middle and upper groups provide broad planning options, but the documented middle gap remains a hard evidence point. Create a channel-list comparison that highlights the excluded range and retain it with the country lookup. After automatic channel changes or controller migration, repeat that comparison. Stable client service alone does not prove that the Z-domain constraints are still being enforced.

Deployment evidence worksheet

Power-state acceptance

Measure power after the access point has joined its controller and the planned radios and services are active. Record switch model, port, negotiated power level, LLDP result and any reduced-capability warning. An idle boot result is not sufficient evidence for the deployed power budget. If an injector is proposed, verify its supported use and include its exact identity in the maintained bill of materials rather than treating it as an unspecified accessory.

Ethernet and cabling proof

Preserve the permanent-link test, patch-lead identities, switch port, negotiated Ethernet rate and error counters. Investigate pair faults, excessive length or rate fallback before wireless acceptance begins. A link light only proves connectivity at some rate; it does not demonstrate the intended uplink performance. Tie the cable result to the AP serial so a later throughput problem can be separated from radio, controller and wired-path causes.

Serial-level asset control

Capture chassis serial, base MAC address, carton reference, deployment site, controller assignment and asset owner. Reconcile the identifiers against the purchase line before activation. Multi-unit cartons require an entry for every physical access point; a carton SKU alone cannot show which unit was installed, held as a spare or returned. This record is also needed to trace support entitlement, replacement history and monitoring ownership.

Country approval retention

Save the Cisco compliance lookup result, lookup date, deployment country, approved regulatory token and reviewer. If the destination changes, stop and repeat the approval rather than moving the unit on the strength of an earlier purchase. Compare the controller country setting and available channels with the retained evidence. Regulatory eligibility is a deployment condition and cannot be inferred from connector fit, stock location or a similar-looking part number.

Authentication path test

Commission representative clients through association, authentication, address assignment, DNS and application reachability. Preserve the identity policy used, test client type, result and relevant controller logs. An access point that joins its controller has not yet demonstrated the user path. Repeat the test after any controller, certificate or authentication-service change and retain failures separately from RF or switch-port evidence.

Roaming acceptance

Define the neighboring access points and client types used for roaming validation. Record handoff behavior, interruption observed, authentication result and controller events along the intended movement path. Compare the outcome with the site's design target rather than declaring success from static association. Where this unit replaces an older AP, test both entry and exit from its cell so a local improvement does not hide a boundary problem.

Security baseline

Retain the approved controller policy, management authorization, certificate or trust workflow, client authentication test and logging destination. Confirm behavior on the deployed controller software instead of promising a protocol from the hardware family name. Remove temporary onboarding access and verify administrative reachability after handover. This keeps product identity separate from software-dependent security claims.

Capacity observation

Define the expected concurrent clients, application mix, airtime utilization and channel-width assumptions for this location. After commissioning, capture radio utilization, retry behavior and representative throughput during a meaningful load period. Compare the observation with the survey design and state any shortfall. A peak link rate from a data sheet is not a site capacity result and should not replace measured operating evidence.

Related Aironet 2802 order records

• AIR-AP2802I-ZK910 - compare antenna architecture and regulatory-domain evidence.
• AIR-AP2802I-Z-K9 - compare antenna architecture and regulatory-domain evidence.
• AIR-AP2802I-ZK910C - compare antenna architecture and regulatory-domain evidence.

Official evidence: Cisco Aironet 2800 Series data sheet; Cisco 2800 Series getting started guide; Cisco 2800 Series support and lifecycle page; and Cisco wireless compliance tool.