AIR-AP2802E-TK910C Cisco Aironet 2800e 4x4:3 MU-MIMO Eco-pack 10 APs

AIR-AP2802E-TK910C exact order identity

AIR-AP2802E-TK910C is a Cisco Aironet 2800 Series controller-based 802.11ac Wave 2 access point order. The exact line combines a 2802E indoor access point for external antennas, regulatory-domain token T, and a configurable ten-unit eco-pack.

Antenna boundary

Cisco documents four RP-TNC antenna connectors plus a Smart Antenna connector on the 2802E. Antennas are a separate engineered part of the deployment bill of materials. Before release, record each Cisco-supported antenna part number, connector use, gain, pattern, cable type, cable loss, mounting orientation and local approval. A connector fit alone does not establish RF performance or regulatory suitability.

Order-form boundary

Cisco's ordering convention uses K910C for a configurable ten-access-point eco-pack. Configuration selection and physical quantity are separate acceptance gates: the chosen domain must be approved and ten individual units must be reconciled. Retain the configured-domain evidence with the carton record, then create ten serial-level asset rows. Do not release a partial, mixed-domain or unconfigured carton to installation without a documented correction. Because this is a configurable line, purchasing must retain the finally selected domain on both the authorized quotation and received label. The carton is not the deployable asset: each of the ten access points needs its own serial, location, controller and acceptance result.

T regulatory-domain channel evidence

Cisco's 2800 Series data sheet lists the T profile as 2.4 GHz channels 1-11; 5 GHz blocks at 5.280-5.320, 5.500-5.700 excluding 5.600-5.640, and 5.745-5.825 GHz. The T profile has a short lower block, a middle block with an internal exclusion, and a separate upper block. A generic three-band summary would hide two important boundaries.

Inspect the short lower range and excluded middle sub-block in the controller export. Attach the result to the T-domain destination approval before enabling production radios. Regulatory-domain letters are identifiers, not country names; use Cisco's compliance tool for the actual deployment country and retain the lookup date.

Procurement inference: this profile combines a short lower group with a middle exclusion and an upper group, so two separate checks can be missed by a generic template. Require the controller export to demonstrate both the lower boundary and the middle gap. If either differs, stop activation and review destination settings. Keep the result with the exact T-domain asset through controller upgrades.

Deployment evidence worksheet

Survey-to-install reconciliation

Attach the approved RF survey location, mounting height, orientation, expected client density, channel width and neighboring-radio assumptions to the order. After installation, compare measured coverage and interference with that design. If ceiling construction, antenna placement or obstructions changed, document the deviation and repeat the affected measurements. This provides a site-specific acceptance reason for the exact unit instead of relying on a family data sheet alone.

Quotation substitution gate

Compare antenna form, regulatory token, configuration suffix, pack quantity and complete Cisco part number on the authorized quotation. Treat any changed token as a substitution that requires a new technical and regulatory review. Procurement should not accept a nearby Aironet 2802 line merely because the family name matches. Preserve the approved line, received label and exception decision so the final asset can be traced to the exact order reviewed here.

Controlled spare policy

If purchased as a spare, name the protected site population, compatible controller image, storage location, storage conditions and periodic power-on test. Confirm that regulatory token, antenna architecture and mounting parts match the population it protects. Set a final-use review date. A stored unit can become unsuitable while untouched because controller software, country approval, certificates or network architecture may change.

Monitoring handover

Assign owners for AP reachability, controller join failures, radio utilization, client health and switch-port errors. Confirm that the exact serial appears in inventory and monitoring, then test the alert path. Record dashboard object, notification route and escalation owner. Telemetry that is not tied to an owned asset does not provide a reliable service baseline and will not support later comparison after channel or software changes.

Change-window controls

Document staging evidence, production window, installer, rollback owner and measurable success criteria. Preserve the prior controller or AP state needed for recovery. After the change, close temporary credentials, compare authentication, monitoring and RF results with the approved baseline, and record the final decision. The work is not complete merely because the unit powers on or appears in a controller list.

Capacity observation

Define the expected concurrent clients, application mix, airtime utilization and channel-width assumptions for this location. After commissioning, capture radio utilization, retry behavior and representative throughput during a meaningful load period. Compare the observation with the survey design and state any shortfall. A peak link rate from a data sheet is not a site capacity result and should not replace measured operating evidence.

Replacement dependency map

Map this unit to controller, licenses, authentication services, switch power, cable, bracket, antenna design and monitoring objects. For an end-of-sale platform, state which dependencies can be reused by the planned Catalyst migration and which require change. A nominal access-point replacement can fail when the surrounding platform was never inventoried. Keep the map with the asset rather than only in a one-time project file.

Handover completeness

The handover package should include exact order identity, destination approval, serial record, controller evidence, switch port, mounting or antenna record, user-path tests and named operational owners. Review the package with the receiving team and list unresolved exceptions. A unit is not operationally accepted when important evidence remains only in installer notes, email attachments or an unowned temporary dashboard.

Related Aironet 2802 order records

• AIR-AP2802I-TK910 - compare antenna architecture and regulatory-domain evidence.
• AIR-AP2802I-T-K9C - compare antenna architecture and regulatory-domain evidence.
• AIR-AP2802I-T-K9 - compare antenna architecture and regulatory-domain evidence.

Official evidence: Cisco Aironet 2800 Series data sheet; Cisco 2800 Series getting started guide; Cisco 2800 Series support and lifecycle page; and Cisco wireless compliance tool.