AIR-AP2802E-IK910 Cisco Aironet 2800e Eco-pack 2.4/5 GHz 10 APs

AIR-AP2802E-IK910 exact order identity

AIR-AP2802E-IK910 is a Cisco Aironet 2800 Series controller-based 802.11ac Wave 2 access point order. The exact line combines a 2802E indoor access point for external antennas, regulatory-domain token I, and a fixed-domain ten-unit eco-pack.

Antenna boundary

Cisco documents four RP-TNC antenna connectors plus a Smart Antenna connector on the 2802E. Antennas are a separate engineered part of the deployment bill of materials. Before release, record each Cisco-supported antenna part number, connector use, gain, pattern, cable type, cable loss, mounting orientation and local approval. A connector fit alone does not establish RF performance or regulatory suitability.

Order-form boundary

Cisco's ordering convention uses K910 for a ten-access-point eco-pack. The carton part number does not replace serial-level control, and all ten units must retain the stated regulatory-domain identity. Reconcile ten chassis serials and MAC addresses against the carton and purchase line. Assign every unit to a destination and controller record; a quantity shortage, mixed domain or substituted antenna form is a receiving exception. Because this is a fixed-domain line, a quotation or received label carrying another domain is a different order and requires a fresh approval. The carton is not the deployable asset: each of the ten access points needs its own serial, location, controller and acceptance result.

I regulatory-domain channel evidence

Cisco's 2800 Series data sheet lists the I profile as 2.4 GHz channels 1-13 and the 5.180-5.320 GHz lower block. The I profile listed by Cisco is confined to the lower 5 GHz block. Designs that depend on middle or upper 5 GHz capacity need revision before this SKU can be approved.

Commission with a lower-block-only channel plan and preserve the controller export. Recalculate co-channel reuse if the pre-purchase survey assumed additional 5 GHz spectrum. Regulatory-domain letters are identifiers, not country names; use Cisco's compliance tool for the actual deployment country and retain the lookup date.

Procurement inference: the lower-block-only 5 GHz plan places a tighter ceiling on channel diversity than profiles with middle or upper groups. Capacity approval should therefore show the client load, channel width and reuse plan that fit within this listed range. If the access point is a spare, verify that the protected population uses the same I-domain constraints before assigning it to emergency replacement stock.

Deployment evidence worksheet

Controller join evidence

Stage the access point on the controller release intended for production. Retain the controller model, software version, discovery path, authorization method and first successful CAPWAP join. Confirm that configuration download completes and that both radios reach an expected operational state. Remove any temporary staging authorization before handover. This evidence separates an orderable access point from a unit that has actually been proven compatible with the planned controller environment.

Ethernet and cabling proof

Preserve the permanent-link test, patch-lead identities, switch port, negotiated Ethernet rate and error counters. Investigate pair faults, excessive length or rate fallback before wireless acceptance begins. A link light only proves connectivity at some rate; it does not demonstrate the intended uplink performance. Tie the cable result to the AP serial so a later throughput problem can be separated from radio, controller and wired-path causes.

Survey-to-install reconciliation

Attach the approved RF survey location, mounting height, orientation, expected client density, channel width and neighboring-radio assumptions to the order. After installation, compare measured coverage and interference with that design. If ceiling construction, antenna placement or obstructions changed, document the deviation and repeat the affected measurements. This provides a site-specific acceptance reason for the exact unit instead of relying on a family data sheet alone.

Quotation substitution gate

Compare antenna form, regulatory token, configuration suffix, pack quantity and complete Cisco part number on the authorized quotation. Treat any changed token as a substitution that requires a new technical and regulatory review. Procurement should not accept a nearby Aironet 2802 line merely because the family name matches. Preserve the approved line, received label and exception decision so the final asset can be traced to the exact order reviewed here.

Software lifecycle file

Record the controller release approved for this unit, the source used to verify support, the last tested date and the owner for software advisories. Available hardware does not prove compatibility with a current or future controller train. Review Cisco support information before every expansion or replacement. The lifecycle file should also state when this Aironet generation must leave service and which surrounding dependencies need migration.

Capacity observation

Define the expected concurrent clients, application mix, airtime utilization and channel-width assumptions for this location. After commissioning, capture radio utilization, retry behavior and representative throughput during a meaningful load period. Compare the observation with the survey design and state any shortfall. A peak link rate from a data sheet is not a site capacity result and should not replace measured operating evidence.

Receiving inspection

At receipt, compare model label, regulatory token, antenna form, quantity, serials and visible condition with the authorized order. Photograph labels before cartons are separated. Quarantine shortages, mixed units, damaged connectors or unapproved substitutions. Do not rely on a distributor description as evidence that the exact Cisco order arrived. Close the inspection only when every physical unit is accounted for.

Operational log retention

Store the initial controller events, switch-port state, radio assignment, channel list and client test results with a consistent asset identifier. Define how long commissioning evidence is retained and who can retrieve it. A later firmware, controller or RF change should add a new dated observation rather than overwrite the original. The resulting history supports lifecycle decisions and distinguishes a new regression from the accepted baseline.

Related Aironet 2802 order records

• AIR-AP2802I-IK910C - compare antenna architecture and regulatory-domain evidence.
• AIR-AP2802I-I-K9C - compare antenna architecture and regulatory-domain evidence.
• AIR-AP2802I-I-K9 - compare antenna architecture and regulatory-domain evidence.

Official evidence: Cisco Aironet 2800 Series data sheet; Cisco 2800 Series getting started guide; Cisco 2800 Series support and lifecycle page; and Cisco wireless compliance tool.