AIR-AP2802E-HK910 Cisco Aironet 2800e 4x4:3 MU-MIMO Dual-band 10 APs

AIR-AP2802E-HK910 exact order identity

AIR-AP2802E-HK910 is a Cisco Aironet 2800 Series controller-based 802.11ac Wave 2 access point order. The exact line combines a 2802E indoor access point for external antennas, regulatory-domain token H, and a fixed-domain ten-unit eco-pack.

Antenna boundary

Cisco documents four RP-TNC antenna connectors plus a Smart Antenna connector on the 2802E. Antennas are a separate engineered part of the deployment bill of materials. Before release, record each Cisco-supported antenna part number, connector use, gain, pattern, cable type, cable loss, mounting orientation and local approval. A connector fit alone does not establish RF performance or regulatory suitability.

Order-form boundary

Cisco's ordering convention uses K910 for a ten-access-point eco-pack. The carton part number does not replace serial-level control, and all ten units must retain the stated regulatory-domain identity. Reconcile ten chassis serials and MAC addresses against the carton and purchase line. Assign every unit to a destination and controller record; a quantity shortage, mixed domain or substituted antenna form is a receiving exception. Because this is a fixed-domain line, a quotation or received label carrying another domain is a different order and requires a fresh approval. The carton is not the deployable asset: each of the ten access points needs its own serial, location, controller and acceptance result.

H regulatory-domain channel evidence

Cisco's 2800 Series data sheet lists the H profile as 2.4 GHz channels 1-13; 5 GHz blocks at 5.150-5.350 and 5.745-5.825 GHz. The H profile starts its lower 5 GHz range at 5.150 GHz and also provides a separated upper block. That lower boundary distinguishes it from nearby domain profiles.

Capture the controller's complete lower-range and upper-range channel output. Match it to the approved H-domain destination and investigate a template that begins at a different lower boundary. Regulatory-domain letters are identifiers, not country names; use Cisco's compliance tool for the actual deployment country and retain the lookup date.

Procurement inference: because the lower group begins below the more common 5.180 GHz boundary, country approval and controller output must be read together. Do not infer that every channel inside the numerical span is available at the destination. Preserve the exact enabled-channel export and associate post-install measurements with it so later troubleshooting can distinguish a regulatory change from an RF-performance change.

Deployment evidence worksheet

Power-state acceptance

Measure power after the access point has joined its controller and the planned radios and services are active. Record switch model, port, negotiated power level, LLDP result and any reduced-capability warning. An idle boot result is not sufficient evidence for the deployed power budget. If an injector is proposed, verify its supported use and include its exact identity in the maintained bill of materials rather than treating it as an unspecified accessory.

Serial-level asset control

Capture chassis serial, base MAC address, carton reference, deployment site, controller assignment and asset owner. Reconcile the identifiers against the purchase line before activation. Multi-unit cartons require an entry for every physical access point; a carton SKU alone cannot show which unit was installed, held as a spare or returned. This record is also needed to trace support entitlement, replacement history and monitoring ownership.

Controlled spare policy

If purchased as a spare, name the protected site population, compatible controller image, storage location, storage conditions and periodic power-on test. Confirm that regulatory token, antenna architecture and mounting parts match the population it protects. Set a final-use review date. A stored unit can become unsuitable while untouched because controller software, country approval, certificates or network architecture may change.

Authentication path test

Commission representative clients through association, authentication, address assignment, DNS and application reachability. Preserve the identity policy used, test client type, result and relevant controller logs. An access point that joins its controller has not yet demonstrated the user path. Repeat the test after any controller, certificate or authentication-service change and retain failures separately from RF or switch-port evidence.

Change-window controls

Document staging evidence, production window, installer, rollback owner and measurable success criteria. Preserve the prior controller or AP state needed for recovery. After the change, close temporary credentials, compare authentication, monitoring and RF results with the approved baseline, and record the final decision. The work is not complete merely because the unit powers on or appears in a controller list.

Security baseline

Retain the approved controller policy, management authorization, certificate or trust workflow, client authentication test and logging destination. Confirm behavior on the deployed controller software instead of promising a protocol from the hardware family name. Remove temporary onboarding access and verify administrative reachability after handover. This keeps product identity separate from software-dependent security claims.

Receiving inspection

At receipt, compare model label, regulatory token, antenna form, quantity, serials and visible condition with the authorized order. Photograph labels before cartons are separated. Quarantine shortages, mixed units, damaged connectors or unapproved substitutions. Do not rely on a distributor description as evidence that the exact Cisco order arrived. Close the inspection only when every physical unit is accounted for.

Fault-domain separation

Build the acceptance record so power, wired link, controller join, radio state, authentication and application reachability can be reviewed independently. Preserve timestamps and device identifiers across switch and controller logs. When a test fails, identify the failing boundary before replacing hardware. This avoids classifying a cable, policy or controller problem as an access-point defect and creates evidence that can be reused during support escalation.

Related Aironet 2802 order records

• AIR-AP2802I-H-K9C - compare antenna architecture and regulatory-domain evidence.
• AIR-AP2802I-HK910C - compare antenna architecture and regulatory-domain evidence.
• AIR-AP2802I-HK910 - compare antenna architecture and regulatory-domain evidence.

Official evidence: Cisco Aironet 2800 Series data sheet; Cisco 2800 Series getting started guide; Cisco 2800 Series support and lifecycle page; and Cisco wireless compliance tool.