AIR-AP2802E-F-K9 Cisco Aironet 2800e 4x4 MU-MIMO 802.11ac Wave 2 AP

AIR-AP2802E-F-K9 exact order identity

AIR-AP2802E-F-K9 is a Cisco Aironet 2800 Series controller-based 802.11ac Wave 2 access point order. The exact line combines a 2802E indoor access point for external antennas, regulatory-domain token F, and a single-unit, fixed regulatory-domain order.

Antenna boundary

Cisco documents four RP-TNC antenna connectors plus a Smart Antenna connector on the 2802E. Antennas are a separate engineered part of the deployment bill of materials. Before release, record each Cisco-supported antenna part number, connector use, gain, pattern, cable type, cable loss, mounting orientation and local approval. A connector fit alone does not establish RF performance or regulatory suitability.

Order-form boundary

Cisco's ordering convention uses K9 for one access point. This line already carries a regulatory-domain token, so receiving must match the complete part number rather than accepting another domain as an equivalent. Create one asset record for the chassis serial and MAC address. Link that record to the approved destination, controller, switch port, mounting position and compliance lookup before the unit joins production. Because this is a fixed-domain line, a quotation or received label carrying another domain is a different order and requires a fresh approval. The single unit needs one serial-level record, while accessories, controller readiness and destination approval remain separate acceptance items.

F regulatory-domain channel evidence

Cisco's 2800 Series data sheet lists the F profile as 2.4 GHz channels 1-13; 5 GHz blocks at 5.250-5.350 and 5.725-5.825 GHz. The F profile is split between a compact mid-lower block and a high block. It does not match the common 5.180 GHz starting point, so imported controller templates require deliberate review.

Validate both separated channel groups on the target controller and confirm that the RF survey used the same boundaries. Record any disabled channel and its local regulatory reason. Regulatory-domain letters are identifiers, not country names; use Cisco's compliance tool for the actual deployment country and retain the lookup date.

Procurement inference: the two separated 5 GHz ranges call for a survey that distinguishes the mid-lower group from the high group. Confirm that expected clients, neighboring radios and controller policy can use the approved choices at the destination. When replacing a unit from a different domain, do not preserve old channel assignments blindly; generate a new assignment and compare measured interference in both F-profile groups.

Deployment evidence worksheet

Power-state acceptance

Measure power after the access point has joined its controller and the planned radios and services are active. Record switch model, port, negotiated power level, LLDP result and any reduced-capability warning. An idle boot result is not sufficient evidence for the deployed power budget. If an injector is proposed, verify its supported use and include its exact identity in the maintained bill of materials rather than treating it as an unspecified accessory.

Ethernet and cabling proof

Preserve the permanent-link test, patch-lead identities, switch port, negotiated Ethernet rate and error counters. Investigate pair faults, excessive length or rate fallback before wireless acceptance begins. A link light only proves connectivity at some rate; it does not demonstrate the intended uplink performance. Tie the cable result to the AP serial so a later throughput problem can be separated from radio, controller and wired-path causes.

Survey-to-install reconciliation

Attach the approved RF survey location, mounting height, orientation, expected client density, channel width and neighboring-radio assumptions to the order. After installation, compare measured coverage and interference with that design. If ceiling construction, antenna placement or obstructions changed, document the deviation and repeat the affected measurements. This provides a site-specific acceptance reason for the exact unit instead of relying on a family data sheet alone.

Country approval retention

Save the Cisco compliance lookup result, lookup date, deployment country, approved regulatory token and reviewer. If the destination changes, stop and repeat the approval rather than moving the unit on the strength of an earlier purchase. Compare the controller country setting and available channels with the retained evidence. Regulatory eligibility is a deployment condition and cannot be inferred from connector fit, stock location or a similar-looking part number.

Controlled spare policy

If purchased as a spare, name the protected site population, compatible controller image, storage location, storage conditions and periodic power-on test. Confirm that regulatory token, antenna architecture and mounting parts match the population it protects. Set a final-use review date. A stored unit can become unsuitable while untouched because controller software, country approval, certificates or network architecture may change.

Capacity observation

Define the expected concurrent clients, application mix, airtime utilization and channel-width assumptions for this location. After commissioning, capture radio utilization, retry behavior and representative throughput during a meaningful load period. Compare the observation with the survey design and state any shortfall. A peak link rate from a data sheet is not a site capacity result and should not replace measured operating evidence.

Receiving inspection

At receipt, compare model label, regulatory token, antenna form, quantity, serials and visible condition with the authorized order. Photograph labels before cartons are separated. Quarantine shortages, mixed units, damaged connectors or unapproved substitutions. Do not rely on a distributor description as evidence that the exact Cisco order arrived. Close the inspection only when every physical unit is accounted for.

Handover completeness

The handover package should include exact order identity, destination approval, serial record, controller evidence, switch port, mounting or antenna record, user-path tests and named operational owners. Review the package with the receiving team and list unresolved exceptions. A unit is not operationally accepted when important evidence remains only in installer notes, email attachments or an unowned temporary dashboard.

Related Aironet 2802 order records

• AIR-AP2802I-FK910C - compare antenna architecture and regulatory-domain evidence.
• AIR-AP2802I-FK910 - compare antenna architecture and regulatory-domain evidence.
• AIR-AP2802I-F-K9C - compare antenna architecture and regulatory-domain evidence.

Official evidence: Cisco Aironet 2800 Series data sheet; Cisco 2800 Series getting started guide; Cisco 2800 Series support and lifecycle page; and Cisco wireless compliance tool.