AIR-AP3802I-SK910C - Cisco Aironet 3800i Access Point Configurable

AIR-AP3802I-SK910C Order Identity

AIR-AP3802I-SK910C is a Cisco Aironet 3800 Series, controller-based 802.11ac Wave 2 access point order. This exact SKU is a 3802I internal-antenna access point, carries regulatory-domain token S, and uses a configurable 10-unit eco-pack.

Antenna and quantity boundary

Integrated antennas; no external antenna is included or selected as part of this SKU. Confirm the mounting position, ceiling construction and intended coverage because antenna orientation is determined by the integrated-antenna enclosure.

Cisco identifies the K910 order form as an eco-pack containing 10 access points; carton-level receiving must reconcile all ten serial numbers.

The C suffix marks a configurable order form. The final Cisco quotation must preserve the selected regulatory domain and any configuration choices; the suffix does not make the unit globally deployable.

Regulatory-domain control

The order carries regulatory-domain token S. Treat that token as an identifier, not a country name. Complete order-country consistency and local spectrum validation against Cisco's current compliance resources before shipment or activation.

Cisco uses the variable regulatory-domain position in its ordering structure. Deployment eligibility must be checked for the destination country; this page does not infer a country mapping from token S.

Controller readiness

Record the intended Cisco wireless controller, supported software train and join method. Validate the AP on a staging network before changing the production RF plan. The acceptance file should identify the controller address, discovery path, AP authorization method and the release evidence used for approval. Capture the first successful join, configuration download and radio state, then remove any temporary staging authorization. This makes a later controller migration traceable without claiming that every software release supports the hardware.

Power budget

Confirm the switch port's negotiated PoE mode, available power, cable length and LLDP behavior. Keep the measured power result with commissioning evidence. Measure the power state after both radios and production features are active, not only while the unit is idle. Record switch model, port, power class, negotiated result and any feature reduction shown by the controller. If an injector is proposed, verify its Cisco support and place it in the maintained bill of materials.

RF survey

Associate this order with the survey location, channel plan and expected client density. Re-survey after installation if mounting or antenna conditions differ from design. The survey record should show mounting height, obstructions, neighboring radios, channel width and the client mix used for capacity planning. Compare measured post-install coverage with the design and document any power, channel or placement adjustment. This gives the exact order a site-specific purpose beyond a generic product description.

Cable qualification

Test the permanent link and preserve the cable result, patch-cord identity and switch port. A successful low-speed link does not prove multigigabit readiness. Store the certification result for the permanent link and both patch leads, including the test standard and date. Investigate pair faults, excessive length and negotiation fallback before AP commissioning. Link the cable record to the switch port and AP serial so later throughput problems can be separated from radio behavior.

Spare policy

State whether the unit is production capacity, a cold spare or a replacement. Define firmware, storage, periodic test and ownership requirements for unused stock. A spare should have a named site scope, compatible controller image, storage condition and periodic power-on test. Record whether its regulatory domain, antenna form and mounting kit match the protected population. Before use, repeat compliance and software checks because suitability can change while the unit is held in stock.

Order reconciliation

Match the exact regulatory-domain token, antenna form, configurable suffix and unit quantity on the Cisco quotation before accepting a substitute. The purchase review should compare every meaningful token in the quoted model with the requested line and this page. Record whether the order is single or ten-unit, internal or external antenna, configurable or fixed-domain. Any substitution requires a new regulatory, antenna, quantity and lifecycle review before acceptance.

Lifecycle and migration evidence

Cisco's support site lists an end-of-life announcement for the Aironet 3800 Series. Confirm current support dates, controller compatibility and the approved replacement path before treating available stock as suitable for a new deployment.

Related 3802I internal-antenna access point records

• AIR-AP3802I-FK910C
• AIR-AP3802I-GK910C
• AIR-AP3802I-IK910C

Official evidence: Cisco Aironet 3800 Series data sheet, Cisco 3800 Series getting started guide, and Cisco end-of-life notices.