AIR-AP2802I-G-K9C Cisco Aironet 2800i Indoor Dual-radio Access Point

AIR-AP2802I-G-K9C exact order identity

AIR-AP2802I-G-K9C is a Cisco Aironet 2800 Series controller-based 802.11ac Wave 2 access point order. The exact line combines a 2802I indoor access point with integrated antennas, regulatory-domain token G, and a single-unit, configurable order.

Antenna boundary

Cisco documents twelve cross-polarized internal antennas in the 2802I enclosure. No external antenna is selected by this access-point SKU. The RF result therefore depends on enclosure orientation, mounting height, obstructions and the surveyed placement. Receiving should confirm the mounting kit, while commissioning should retain photographs of the final orientation and compare measured coverage with the approved survey.

Order-form boundary

Cisco's ordering convention uses K9C for a configurable single unit. The C suffix does not make the access point globally deployable; the final configured domain and destination approval must still be present on the quotation and received label. Hold the unit at receiving if the configured domain is absent or differs from the approved order. Preserve the configuration selection, chassis serial, destination evidence and controller-domain check as one release record. Because this is a configurable line, purchasing must retain the finally selected domain on both the authorized quotation and received label. The single unit needs one serial-level record, while accessories, controller readiness and destination approval remain separate acceptance items.

G regulatory-domain channel evidence

Cisco's 2800 Series data sheet lists the G profile as 2.4 GHz channels 1-13 and the 5.745-5.825 GHz upper block. Cisco lists the G profile with an upper 5 GHz block and no lower or middle 5 GHz block. This changes available channel count and makes destination-specific capacity validation important.

Use an upper-band-specific commissioning checklist. Confirm controller country, available channel list and post-install utilization before accepting a design that was sized using another domain. Regulatory-domain letters are identifiers, not country names; use Cisco's compliance tool for the actual deployment country and retain the lookup date.

Procurement inference: the listed upper-only 5 GHz choice makes channel reuse and client compatibility central to acceptance. Record the client mix used during testing and verify association on approved upper-block channels. If the site's earlier survey relied on lower or DFS middle channels, the design requires revision rather than a simple model substitution, even when antenna architecture and controller family remain unchanged.

Deployment evidence worksheet

Controller join evidence

Stage the access point on the controller release intended for production. Retain the controller model, software version, discovery path, authorization method and first successful CAPWAP join. Confirm that configuration download completes and that both radios reach an expected operational state. Remove any temporary staging authorization before handover. This evidence separates an orderable access point from a unit that has actually been proven compatible with the planned controller environment.

Country approval retention

Save the Cisco compliance lookup result, lookup date, deployment country, approved regulatory token and reviewer. If the destination changes, stop and repeat the approval rather than moving the unit on the strength of an earlier purchase. Compare the controller country setting and available channels with the retained evidence. Regulatory eligibility is a deployment condition and cannot be inferred from connector fit, stock location or a similar-looking part number.

Quotation substitution gate

Compare antenna form, regulatory token, configuration suffix, pack quantity and complete Cisco part number on the authorized quotation. Treat any changed token as a substitution that requires a new technical and regulatory review. Procurement should not accept a nearby Aironet 2802 line merely because the family name matches. Preserve the approved line, received label and exception decision so the final asset can be traced to the exact order reviewed here.

Controlled spare policy

If purchased as a spare, name the protected site population, compatible controller image, storage location, storage conditions and periodic power-on test. Confirm that regulatory token, antenna architecture and mounting parts match the population it protects. Set a final-use review date. A stored unit can become unsuitable while untouched because controller software, country approval, certificates or network architecture may change.

Interference baseline

Preserve the pre-install and post-install noise, neighboring-radio and channel-occupancy observations for the selected location. Record any controller-driven channel change during acceptance. If the regulatory profile limits the channel choices, state how that constraint affected reuse and mitigation. This baseline gives future troubleshooting a reference point and prevents an unrelated interference change from being attributed to the hardware order.

Receiving inspection

At receipt, compare model label, regulatory token, antenna form, quantity, serials and visible condition with the authorized order. Photograph labels before cartons are separated. Quarantine shortages, mixed units, damaged connectors or unapproved substitutions. Do not rely on a distributor description as evidence that the exact Cisco order arrived. Close the inspection only when every physical unit is accounted for.

Operational log retention

Store the initial controller events, switch-port state, radio assignment, channel list and client test results with a consistent asset identifier. Define how long commissioning evidence is retained and who can retrieve it. A later firmware, controller or RF change should add a new dated observation rather than overwrite the original. The resulting history supports lifecycle decisions and distinguishes a new regression from the accepted baseline.

Handover completeness

The handover package should include exact order identity, destination approval, serial record, controller evidence, switch port, mounting or antenna record, user-path tests and named operational owners. Review the package with the receiving team and list unresolved exceptions. A unit is not operationally accepted when important evidence remains only in installer notes, email attachments or an unowned temporary dashboard.

Related Aironet 2802 order records

• AIR-AP2802E-GK910C - compare antenna architecture and regulatory-domain evidence.
• AIR-AP2802E-GK910 - compare antenna architecture and regulatory-domain evidence.
• AIR-AP2802E-G-K9 - compare antenna architecture and regulatory-domain evidence.

Official evidence: Cisco Aironet 2800 Series data sheet; Cisco 2800 Series getting started guide; Cisco 2800 Series support and lifecycle page; and Cisco wireless compliance tool.