AIR-AP2802I-EK910 Cisco Aironet 2800i Enterprise Eco-pack Access Point

AIR-AP2802I-EK910 exact order identity

AIR-AP2802I-EK910 is a Cisco Aironet 2800 Series controller-based 802.11ac Wave 2 access point order. The exact line combines a 2802I indoor access point with integrated antennas, regulatory-domain token E, and a fixed-domain ten-unit eco-pack.

Antenna boundary

Cisco documents twelve cross-polarized internal antennas in the 2802I enclosure. No external antenna is selected by this access-point SKU. The RF result therefore depends on enclosure orientation, mounting height, obstructions and the surveyed placement. Receiving should confirm the mounting kit, while commissioning should retain photographs of the final orientation and compare measured coverage with the approved survey.

Order-form boundary

Cisco's ordering convention uses K910 for a ten-access-point eco-pack. The carton part number does not replace serial-level control, and all ten units must retain the stated regulatory-domain identity. Reconcile ten chassis serials and MAC addresses against the carton and purchase line. Assign every unit to a destination and controller record; a quantity shortage, mixed domain or substituted antenna form is a receiving exception. Because this is a fixed-domain line, a quotation or received label carrying another domain is a different order and requires a fresh approval. The carton is not the deployable asset: each of the ten access points needs its own serial, location, controller and acceptance result.

E regulatory-domain channel evidence

Cisco's 2800 Series data sheet lists the E profile as 2.4 GHz channels 1-13; 5 GHz blocks at 5.180-5.320 and 5.500-5.700 GHz, excluding 5.600-5.640 GHz. The E profile combines lower and middle 5 GHz operation but documents an internal exclusion in the middle block. Survey and controller evidence must show that the gap was understood.

Compare the enabled channel export with the E-domain profile, paying particular attention to the excluded sub-block. Preserve the lookup date, country selection and controller result in the asset file. Regulatory-domain letters are identifiers, not country names; use Cisco's compliance tool for the actual deployment country and retain the lookup date.

Procurement inference: this profile's excluded middle sub-block creates a specific migration check. Preserve the prior controller channel template, then prove that the new or restored template does not reintroduce the excluded range. If channel capacity was calculated from a continuous middle block, correct the design assumptions and record the narrower usable plan before installation approval.

Deployment evidence worksheet

Quotation substitution gate

Compare antenna form, regulatory token, configuration suffix, pack quantity and complete Cisco part number on the authorized quotation. Treat any changed token as a substitution that requires a new technical and regulatory review. Procurement should not accept a nearby Aironet 2802 line merely because the family name matches. Preserve the approved line, received label and exception decision so the final asset can be traced to the exact order reviewed here.

Software lifecycle file

Record the controller release approved for this unit, the source used to verify support, the last tested date and the owner for software advisories. Available hardware does not prove compatibility with a current or future controller train. Review Cisco support information before every expansion or replacement. The lifecycle file should also state when this Aironet generation must leave service and which surrounding dependencies need migration.

Roaming acceptance

Define the neighboring access points and client types used for roaming validation. Record handoff behavior, interruption observed, authentication result and controller events along the intended movement path. Compare the outcome with the site's design target rather than declaring success from static association. Where this unit replaces an older AP, test both entry and exit from its cell so a local improvement does not hide a boundary problem.

Monitoring handover

Assign owners for AP reachability, controller join failures, radio utilization, client health and switch-port errors. Confirm that the exact serial appears in inventory and monitoring, then test the alert path. Record dashboard object, notification route and escalation owner. Telemetry that is not tied to an owned asset does not provide a reliable service baseline and will not support later comparison after channel or software changes.

Change-window controls

Document staging evidence, production window, installer, rollback owner and measurable success criteria. Preserve the prior controller or AP state needed for recovery. After the change, close temporary credentials, compare authentication, monitoring and RF results with the approved baseline, and record the final decision. The work is not complete merely because the unit powers on or appears in a controller list.

Interference baseline

Preserve the pre-install and post-install noise, neighboring-radio and channel-occupancy observations for the selected location. Record any controller-driven channel change during acceptance. If the regulatory profile limits the channel choices, state how that constraint affected reuse and mitigation. This baseline gives future troubleshooting a reference point and prevents an unrelated interference change from being attributed to the hardware order.

Receiving inspection

At receipt, compare model label, regulatory token, antenna form, quantity, serials and visible condition with the authorized order. Photograph labels before cartons are separated. Quarantine shortages, mixed units, damaged connectors or unapproved substitutions. Do not rely on a distributor description as evidence that the exact Cisco order arrived. Close the inspection only when every physical unit is accounted for.

Operational log retention

Store the initial controller events, switch-port state, radio assignment, channel list and client test results with a consistent asset identifier. Define how long commissioning evidence is retained and who can retrieve it. A later firmware, controller or RF change should add a new dated observation rather than overwrite the original. The resulting history supports lifecycle decisions and distinguishes a new regression from the accepted baseline.

Related Aironet 2802 order records

• AIR-AP2802E-EK910C - compare antenna architecture and regulatory-domain evidence.
• AIR-AP2802E-E-K9C - compare antenna architecture and regulatory-domain evidence.
• AIR-AP2802E-E-K9 - compare antenna architecture and regulatory-domain evidence.

Official evidence: Cisco Aironet 2800 Series data sheet; Cisco 2800 Series getting started guide; Cisco 2800 Series support and lifecycle page; and Cisco wireless compliance tool.