AIR-AP2802I-CK910C Cisco Aironet 2800i Indoor WiFi 5 Eco-pack 10 APs

AIR-AP2802I-CK910C exact order identity

AIR-AP2802I-CK910C is a Cisco Aironet 2800 Series controller-based 802.11ac Wave 2 access point order. The exact line combines a 2802I indoor access point with integrated antennas, regulatory-domain token C, and a configurable ten-unit eco-pack.

Antenna boundary

Cisco documents twelve cross-polarized internal antennas in the 2802I enclosure. No external antenna is selected by this access-point SKU. The RF result therefore depends on enclosure orientation, mounting height, obstructions and the surveyed placement. Receiving should confirm the mounting kit, while commissioning should retain photographs of the final orientation and compare measured coverage with the approved survey.

Order-form boundary

Cisco's ordering convention uses K910C for a configurable ten-access-point eco-pack. Configuration selection and physical quantity are separate acceptance gates: the chosen domain must be approved and ten individual units must be reconciled. Retain the configured-domain evidence with the carton record, then create ten serial-level asset rows. Do not release a partial, mixed-domain or unconfigured carton to installation without a documented correction. Because this is a configurable line, purchasing must retain the finally selected domain on both the authorized quotation and received label. The carton is not the deployable asset: each of the ten access points needs its own serial, location, controller and acceptance result.

C regulatory-domain channel evidence

Cisco's 2800 Series data sheet lists the C profile as 2.4 GHz channels 1-13 and the 5.745-5.825 GHz upper block. The C profile listed by Cisco does not include the lower or middle 5 GHz blocks shown for many other domains. That narrower 5 GHz choice can materially change capacity and channel reuse assumptions.

Reject a design copied from a lower-band domain. Commission the site against the upper-block channel set, record the controller country setting and repeat the survey if the original design assumed unavailable 5 GHz channels. Regulatory-domain letters are identifiers, not country names; use Cisco's compliance tool for the actual deployment country and retain the lookup date.

Procurement inference: this is an upper-5-GHz-focused profile in Cisco's table, so the buying decision should be based on a survey that can operate without lower or middle 5 GHz choices. Check client and infrastructure support for the selected operating plan at the actual site. A successful bench join in a different country or controller setting does not validate the channel availability required by the deployment.

Deployment evidence worksheet

Power-state acceptance

Measure power after the access point has joined its controller and the planned radios and services are active. Record switch model, port, negotiated power level, LLDP result and any reduced-capability warning. An idle boot result is not sufficient evidence for the deployed power budget. If an injector is proposed, verify its supported use and include its exact identity in the maintained bill of materials rather than treating it as an unspecified accessory.

Ethernet and cabling proof

Preserve the permanent-link test, patch-lead identities, switch port, negotiated Ethernet rate and error counters. Investigate pair faults, excessive length or rate fallback before wireless acceptance begins. A link light only proves connectivity at some rate; it does not demonstrate the intended uplink performance. Tie the cable result to the AP serial so a later throughput problem can be separated from radio, controller and wired-path causes.

Survey-to-install reconciliation

Attach the approved RF survey location, mounting height, orientation, expected client density, channel width and neighboring-radio assumptions to the order. After installation, compare measured coverage and interference with that design. If ceiling construction, antenna placement or obstructions changed, document the deviation and repeat the affected measurements. This provides a site-specific acceptance reason for the exact unit instead of relying on a family data sheet alone.

Serial-level asset control

Capture chassis serial, base MAC address, carton reference, deployment site, controller assignment and asset owner. Reconcile the identifiers against the purchase line before activation. Multi-unit cartons require an entry for every physical access point; a carton SKU alone cannot show which unit was installed, held as a spare or returned. This record is also needed to trace support entitlement, replacement history and monitoring ownership.

Authentication path test

Commission representative clients through association, authentication, address assignment, DNS and application reachability. Preserve the identity policy used, test client type, result and relevant controller logs. An access point that joins its controller has not yet demonstrated the user path. Repeat the test after any controller, certificate or authentication-service change and retain failures separately from RF or switch-port evidence.

Monitoring handover

Assign owners for AP reachability, controller join failures, radio utilization, client health and switch-port errors. Confirm that the exact serial appears in inventory and monitoring, then test the alert path. Record dashboard object, notification route and escalation owner. Telemetry that is not tied to an owned asset does not provide a reliable service baseline and will not support later comparison after channel or software changes.

Receiving inspection

At receipt, compare model label, regulatory token, antenna form, quantity, serials and visible condition with the authorized order. Photograph labels before cartons are separated. Quarantine shortages, mixed units, damaged connectors or unapproved substitutions. Do not rely on a distributor description as evidence that the exact Cisco order arrived. Close the inspection only when every physical unit is accounted for.

Operational log retention

Store the initial controller events, switch-port state, radio assignment, channel list and client test results with a consistent asset identifier. Define how long commissioning evidence is retained and who can retrieve it. A later firmware, controller or RF change should add a new dated observation rather than overwrite the original. The resulting history supports lifecycle decisions and distinguishes a new regression from the accepted baseline.

Related Aironet 2802 order records

• AIR-AP2802E-CK910 - compare antenna architecture and regulatory-domain evidence.
• AIR-AP2802E-C-K9C - compare antenna architecture and regulatory-domain evidence.
• AIR-AP2802E-CK910C - compare antenna architecture and regulatory-domain evidence.

Official evidence: Cisco Aironet 2800 Series data sheet; Cisco 2800 Series getting started guide; Cisco 2800 Series support and lifecycle page; and Cisco wireless compliance tool.