AIR-AP2802E-D-K9 Cisco Aironet 2800e Dual-band 802.11ac Wave 2 AP

AIR-AP2802E-D-K9 exact order identity

AIR-AP2802E-D-K9 is a Cisco Aironet 2800 Series controller-based 802.11ac Wave 2 access point order. The exact line combines a 2802E indoor access point for external antennas, regulatory-domain token D, and a single-unit, fixed regulatory-domain order.

Antenna boundary

Cisco documents four RP-TNC antenna connectors plus a Smart Antenna connector on the 2802E. Antennas are a separate engineered part of the deployment bill of materials. Before release, record each Cisco-supported antenna part number, connector use, gain, pattern, cable type, cable loss, mounting orientation and local approval. A connector fit alone does not establish RF performance or regulatory suitability.

Order-form boundary

Cisco's ordering convention uses K9 for one access point. This line already carries a regulatory-domain token, so receiving must match the complete part number rather than accepting another domain as an equivalent. Create one asset record for the chassis serial and MAC address. Link that record to the approved destination, controller, switch port, mounting position and compliance lookup before the unit joins production. Because this is a fixed-domain line, a quotation or received label carrying another domain is a different order and requires a fresh approval. The single unit needs one serial-level record, while accessories, controller readiness and destination approval remain separate acceptance items.

D regulatory-domain channel evidence

Cisco's 2800 Series data sheet lists the D profile as 2.4 GHz channels 1-11; 5 GHz blocks at 5.180-5.320 and 5.745-5.825 GHz. The D profile uses separated lower and upper 5 GHz blocks with no documented middle block. A channel plan that assumes a continuous 5 GHz range is therefore not suitable evidence for this order.

Verify that the controller presents the two expected 5 GHz groups and excludes an unapproved middle range. Store the result with the deployment country lookup and the exact D-domain quotation. Regulatory-domain letters are identifiers, not country names; use Cisco's compliance tool for the actual deployment country and retain the lookup date.

Procurement inference: the separation between lower and upper 5 GHz groups should be represented as two planning pools. During acceptance, compare utilization and interference in each pool rather than averaging all 5 GHz observations together. If a replacement AP was previously using a middle-range channel under another profile, document the revised reuse plan before treating the D-domain unit as a direct substitution.

Deployment evidence worksheet

Controller join evidence

Stage the access point on the controller release intended for production. Retain the controller model, software version, discovery path, authorization method and first successful CAPWAP join. Confirm that configuration download completes and that both radios reach an expected operational state. Remove any temporary staging authorization before handover. This evidence separates an orderable access point from a unit that has actually been proven compatible with the planned controller environment.

Ethernet and cabling proof

Preserve the permanent-link test, patch-lead identities, switch port, negotiated Ethernet rate and error counters. Investigate pair faults, excessive length or rate fallback before wireless acceptance begins. A link light only proves connectivity at some rate; it does not demonstrate the intended uplink performance. Tie the cable result to the AP serial so a later throughput problem can be separated from radio, controller and wired-path causes.

Survey-to-install reconciliation

Attach the approved RF survey location, mounting height, orientation, expected client density, channel width and neighboring-radio assumptions to the order. After installation, compare measured coverage and interference with that design. If ceiling construction, antenna placement or obstructions changed, document the deviation and repeat the affected measurements. This provides a site-specific acceptance reason for the exact unit instead of relying on a family data sheet alone.

Serial-level asset control

Capture chassis serial, base MAC address, carton reference, deployment site, controller assignment and asset owner. Reconcile the identifiers against the purchase line before activation. Multi-unit cartons require an entry for every physical access point; a carton SKU alone cannot show which unit was installed, held as a spare or returned. This record is also needed to trace support entitlement, replacement history and monitoring ownership.

Authentication path test

Commission representative clients through association, authentication, address assignment, DNS and application reachability. Preserve the identity policy used, test client type, result and relevant controller logs. An access point that joins its controller has not yet demonstrated the user path. Repeat the test after any controller, certificate or authentication-service change and retain failures separately from RF or switch-port evidence.

Capacity observation

Define the expected concurrent clients, application mix, airtime utilization and channel-width assumptions for this location. After commissioning, capture radio utilization, retry behavior and representative throughput during a meaningful load period. Compare the observation with the survey design and state any shortfall. A peak link rate from a data sheet is not a site capacity result and should not replace measured operating evidence.

Replacement dependency map

Map this unit to controller, licenses, authentication services, switch power, cable, bracket, antenna design and monitoring objects. For an end-of-sale platform, state which dependencies can be reused by the planned Catalyst migration and which require change. A nominal access-point replacement can fail when the surrounding platform was never inventoried. Keep the map with the asset rather than only in a one-time project file.

Handover completeness

The handover package should include exact order identity, destination approval, serial record, controller evidence, switch port, mounting or antenna record, user-path tests and named operational owners. Review the package with the receiving team and list unresolved exceptions. A unit is not operationally accepted when important evidence remains only in installer notes, email attachments or an unowned temporary dashboard.

Related Aironet 2802 order records

• AIR-AP2802I-DK910C - compare antenna architecture and regulatory-domain evidence.
• AIR-AP2802I-DK910 - compare antenna architecture and regulatory-domain evidence.
• AIR-AP2802I-D-K9C - compare antenna architecture and regulatory-domain evidence.

Official evidence: Cisco Aironet 2800 Series data sheet; Cisco 2800 Series getting started guide; Cisco 2800 Series support and lifecycle page; and Cisco wireless compliance tool.