AIR-AP1815T-S-K9 Cisco Aironet 1815t Teleworker Access Point

AIR-AP1815T-S-K9 Exact Teleworker Order

AIR-AP1815T-S-K9 is Cisco's S-domain Aironet 1815t controller-based 802.11ac Wave 2 order. The 1815t is designed for teleworker and micro-branch OfficeExtend use; it is not the wall-plate 1815w or the general indoor 1815i.

Remote-office network boundary

The AP supplies one Gigabit WAN/uplink interface and three local Gigabit Ethernet ports while its simultaneous dual-band 2x2 radios provide two spatial streams. Record the ISP handoff, addressing, tunnel/controller reachability and VLAN or policy assignment for each occupied local port.

S-domain compliance evidence

The domain letter is an order-control token rather than a country name. Compare the complete S-domain PID on quotation, carton and asset record; family equivalence is not regulatory equivalence.

Make quotation accuracy the S-domain control. The approved quote, supplier confirmation, received carton and asset record must carry the complete same PID. A substitution request should identify antenna form, controller-image state and regulatory token separately. Only after destination approval and controller review should the replacement line be accepted, even if pricing and lead time are unchanged.

S-domain field acceptance

For the S-domain AP, verify the full PID on quote, carton and controller inventory before activation. Measure voice-call quality and corporate application response through the OfficeExtend tunnel while all occupied local Ethernet ports carry representative traffic.

Power and staging plan

The desktop-oriented unit can use its documented power path and integrated antennas. Stage controller reachability, software, regulatory country, WAN behavior and local ports at the corporate site before shipment, but repeat the WAN and compliance checks at the final destination.

Teleworker operations worksheet

Ethernet and cabling proof

Preserve the permanent-link test, patch-lead identities, switch port, negotiated Ethernet rate and error counters. Investigate pair faults, excessive length or rate fallback before wireless acceptance begins. A link light only proves connectivity at some rate; it does not demonstrate the intended uplink performance. Tie the cable result to the AP serial so a later throughput problem can be separated from radio, controller and wired-path causes. For this S-domain teleworker order, tie the result to the remote-user circuit, controller object and exact AP serial.

Survey-to-install reconciliation

Attach the approved RF survey location, mounting height, orientation, expected client density, channel width and neighboring-radio assumptions to the order. After installation, compare measured coverage and interference with that design. If ceiling construction, antenna placement or obstructions changed, document the deviation and repeat the affected measurements. This provides a site-specific acceptance reason for the exact unit instead of relying on a family data sheet alone. For this S-domain teleworker order, tie the result to the remote-user circuit, controller object and exact AP serial.

Country approval retention

Save the Cisco compliance lookup result, lookup date, deployment country, approved regulatory token and reviewer. If the destination changes, stop and repeat the approval rather than moving the unit on the strength of an earlier purchase. Compare the controller country setting and available channels with the retained evidence. Regulatory eligibility is a deployment condition and cannot be inferred from connector fit, stock location or a similar-looking part number. For this S-domain teleworker order, tie the result to the remote-user circuit, controller object and exact AP serial.

Quotation substitution gate

Compare antenna form, regulatory token, configuration suffix, pack quantity and complete Cisco part number on the authorized quotation. Treat any changed token as a substitution that requires a new technical and regulatory review. Procurement should not accept a nearby Aironet 2802 line merely because the family name matches. Preserve the approved line, received label and exception decision so the final asset can be traced to the exact order reviewed here. For this S-domain teleworker order, tie the result to the remote-user circuit, controller object and exact AP serial.

Lifecycle decision

Cisco lists the Aironet 1815 family as end of sale, gives 30 April 2027 as the last support date and identifies Catalyst 9105AX as the migration family. Compare remote-site WAN behavior, controller architecture, wired-port needs, power and desk placement before choosing a replacement.

Official sources: Cisco Aironet 1815t data sheet, Cisco 1815t getting-started guide, Cisco 1815t teleworker deployment guide, Cisco 1815 lifecycle notice and Cisco compliance lookup.