AIR-AP1815T-H-K9 Cisco Aironet 1815t Teleworker Access Point

AIR-AP1815T-H-K9 Exact Teleworker Order

AIR-AP1815T-H-K9 is Cisco's H-domain Aironet 1815t controller-based 802.11ac Wave 2 order. The 1815t is designed for teleworker and micro-branch OfficeExtend use; it is not the wall-plate 1815w or the general indoor 1815i.

Remote-office network boundary

The AP supplies one Gigabit WAN/uplink interface and three local Gigabit Ethernet ports while its simultaneous dual-band 2x2 radios provide two spatial streams. Record the ISP handoff, addressing, tunnel/controller reachability and VLAN or policy assignment for each occupied local port.

H-domain compliance evidence

The domain letter is an order-control token rather than a country name. Capture the H-domain lookup date, reviewer and destination; a successful controller join does not replace this evidence.

Build the H-domain evidence around staged controller join. Capture the lookup, destination, controller country, software release and first successful join without treating the join itself as regulatory proof. Before production release, a reviewer should reconcile all five fields. A later controller reset or country change should create a new dated result while retaining the accepted baseline.

H-domain field acceptance

For the H-domain unit, create a home-office handover with ISP modem mode, WAN addressing, DNS reachability, controller round-trip time and power recovery. Repeat the test after moving the AP from staging to the employee circuit and archive both results.

Power and staging plan

The desktop-oriented unit can use its documented power path and integrated antennas. Stage controller reachability, software, regulatory country, WAN behavior and local ports at the corporate site before shipment, but repeat the WAN and compliance checks at the final destination.

Teleworker operations worksheet

Controller join evidence

Stage the access point on the controller release intended for production. Retain the controller model, software version, discovery path, authorization method and first successful CAPWAP join. Confirm that configuration download completes and that both radios reach an expected operational state. Remove any temporary staging authorization before handover. This evidence separates an orderable access point from a unit that has actually been proven compatible with the planned controller environment. For this H-domain teleworker order, tie the result to the remote-user circuit, controller object and exact AP serial.

Power-state acceptance

Measure power after the access point has joined its controller and the planned radios and services are active. Record switch model, port, negotiated power level, LLDP result and any reduced-capability warning. An idle boot result is not sufficient evidence for the deployed power budget. If an injector is proposed, verify its supported use and include its exact identity in the maintained bill of materials rather than treating it as an unspecified accessory. For this H-domain teleworker order, tie the result to the remote-user circuit, controller object and exact AP serial.

Ethernet and cabling proof

Preserve the permanent-link test, patch-lead identities, switch port, negotiated Ethernet rate and error counters. Investigate pair faults, excessive length or rate fallback before wireless acceptance begins. A link light only proves connectivity at some rate; it does not demonstrate the intended uplink performance. Tie the cable result to the AP serial so a later throughput problem can be separated from radio, controller and wired-path causes. For this H-domain teleworker order, tie the result to the remote-user circuit, controller object and exact AP serial.

Survey-to-install reconciliation

Attach the approved RF survey location, mounting height, orientation, expected client density, channel width and neighboring-radio assumptions to the order. After installation, compare measured coverage and interference with that design. If ceiling construction, antenna placement or obstructions changed, document the deviation and repeat the affected measurements. This provides a site-specific acceptance reason for the exact unit instead of relying on a family data sheet alone. For this H-domain teleworker order, tie the result to the remote-user circuit, controller object and exact AP serial.

Lifecycle decision

Cisco lists the Aironet 1815 family as end of sale, gives 30 April 2027 as the last support date and identifies Catalyst 9105AX as the migration family. Compare remote-site WAN behavior, controller architecture, wired-port needs, power and desk placement before choosing a replacement.

Official sources: Cisco Aironet 1815t data sheet, Cisco 1815t getting-started guide, Cisco 1815t teleworker deployment guide, Cisco 1815 lifecycle notice and Cisco compliance lookup.