Huawei AP2030DN Wall-Plate Access Point

Start with order reference 50082640 and the required room connections

Huawei’s ordering row names AP2030DN and records five RJ45 and two RJ11 connections. Those counts are explained by the device-structure table: GE/PoE is the network uplink; ETH0–ETH3 serve wired room devices; one Phone role connects to traditional PSTN and the other to a POTS phone or modem. Keep the exact model and reference 50082640 on the quotation and receiving checklist. Confirm the supplied label and adapter scope instead of substituting a similar wall-plate name.

Treat the four Ethernet room ports as Fast Ethernet

The manufacturer assigns 10/100/1000 Mbit/s to GE/PoE but 10/100 Mbit/s to ETH0–ETH3. This arrangement can accommodate four wired room connections, but it does not give each one a Gigabit interface. Check the intended workstation, television or other wired device against that documented link rate. During acceptance, verify the uplink and each requested room port individually; a Gigabit uplink alone does not establish the required downstream link speed.

AP2030DN and AP2030DN-S are not the same wiring choice

The exact AP2030DN-S order row is 50083605. Its separate structure guide lists one 10/100M ETH/PoE connection, and its basic table gives IEEE 802.3af input and 5.1 W consumption. AP2030DN instead provides the Gigabit GE/PoE uplink, four Fast Ethernet room ports, two telephone-interface roles and a 12 V DC socket, with 8.7 W reference consumption. Choose by the actual outlet and power arrangement; the S suffix is not an interchangeable spelling for the five-RJ45 AP2030DN record.

Source the 12 V adapter separately when the DC arrangement is selected

Huawei describes DC 12V as the adapter socket and specifies 12 V ±10% in the AP2030DN power table. The alternative is IEEE 802.3af/at PoE through GE/PoE. The device instructions state that the power adapter is not delivered with the product and must be purchased separately. Confirm the selected adapter, PoE source and cable arrangement in the quotation. The cited interface list does not assign a PoE-output function to the room Ethernet ports.

Check both sides of the wall and keep telephone service separate

The outside-wall height, width and depth are 25 × 140 × 86 mm; the inside-wall dimensions are 16.5 × 51.5 × 63.5 mm. Weight is 0.2 kg. Verify the recess, cabling clearance and mounting arrangement for the supplied revision. The documented POTS/modem and PSTN interfaces are telephone-connection roles, not evidence of a SIP gateway, Ethernet-to-telephone conversion or an included phone-service subscription.

Complete the installation checks with the model’s own limits

The consumption reference is 8.7 W, subject to local rules. Huawei lists 128 MB DDR2 and 32 MB Flash, an operating range of 0°C to +40°C at −60–1800 m, and an upper-temperature reduction of 1°C per 300 m above 1800 m through 5000 m. Humidity is 5–95% non-condensing. Confirm the management equipment, software and intended WLAN client use before commissioning. The order row establishes 802.11ac dual-frequency identity; no Wave 2, MU-MIMO or antenna-gain figure is inferred from AP2030DN-S or the category description.

Document/Firmware Download

• Huawei AP2030DN exact Ethernet, telephone and DC interface table
• Huawei AP2030DN 8.7 W, 12 V and inside/outside-wall specifications
• Huawei AP2030DN ordering reference 50082640 and connector counts
• Huawei AP2030DN-S separate single-port hardware reference
• Huawei AP2030DN-S own 802.3af and 5.1W reference for the comparison
• Huawei AP2030DN-S separate order reference 50083605
• Huawei AP2030DN original numbered interface illustration