AIR-AP3802P-QK910 - Cisco Aironet 3800p Access Point

AIR-AP3802P-QK910 Order Identity

AIR-AP3802P-QK910 is a Cisco Aironet 3800 Series, controller-based 802.11ac Wave 2 access point order. This exact SKU is a 3802P external-antenna access point, carries regulatory-domain token Q, and uses a fixed-domain 10-unit eco-pack.

Antenna and quantity boundary

External antenna system required; verify the exact Cisco-supported antenna and connector arrangement. Treat the antenna design as an engineered item: retain the selected antenna, cable path, mounting method and regulatory approval with the access-point order.

Cisco identifies the K910 order form as an eco-pack containing 10 access points; carton-level receiving must reconcile all ten serial numbers.

This is a non-C fixed-domain order form. Receiving must match the exact domain-bearing SKU and must not substitute a configurable or different-domain line without approval.

Regulatory-domain control

The order carries regulatory-domain token Q. Treat that token as an identifier, not a country name. Complete site-specific compliance evidence and asset registration against Cisco's current compliance resources before shipment or activation.

Cisco uses the variable regulatory-domain position in its ordering structure. Deployment eligibility must be checked for the destination country; this page does not infer a country mapping from token Q.

Controller readiness

Record the intended Cisco wireless controller, supported software train and join method. Validate the AP on a staging network before changing the production RF plan. The acceptance file should identify the controller address, discovery path, AP authorization method and the release evidence used for approval. Capture the first successful join, configuration download and radio state, then remove any temporary staging authorization. This makes a later controller migration traceable without claiming that every software release supports the hardware.

Multigigabit uplink

The 3800 Series supports multigigabit Ethernet. Verify the switch port, cabling category, negotiated rate and error counters instead of assuming a 2.5 or 5 Gbps link. Commissioning should preserve the negotiated Ethernet rate, cable-test result, packet errors and switch configuration. Where the access switch is limited to 1 Gbps, state that design choice explicitly instead of presenting multigigabit capability as achieved throughput. Recheck negotiation after patch-cord or switch changes.

Mounting inventory

List the ceiling or wall bracket, enclosure, safety restraint and access requirements. Receiving should reject a mechanically incomplete deployment kit. Receiving should identify the bracket and any above-ceiling, wall, enclosure or seismic requirement before scheduling installers. Photograph the mounting label and cable entry after installation, and record access constraints for replacement. Missing mechanical parts should be resolved as a bill-of-material exception, not hidden in the AP description.

Cable qualification

Test the permanent link and preserve the cable result, patch-cord identity and switch port. A successful low-speed link does not prove multigigabit readiness. Store the certification result for the permanent link and both patch leads, including the test standard and date. Investigate pair faults, excessive length and negotiation fallback before AP commissioning. Link the cable record to the switch port and AP serial so later throughput problems can be separated from radio behavior.

Antenna governance

Keep antenna identity and approved installation conditions with the AP record. A matching connector alone is not evidence of regulatory or RF suitability. For external-antenna models, preserve manufacturer part numbers, connector arrangement, gain, pattern, cable type, loss and mounting orientation. For internal-antenna models, preserve enclosure orientation and placement constraints. In both cases, compare the installed design with country approval and the RF survey before service acceptance.

Security baseline

Record the approved controller policy, management access, certificate handling and authentication test. Do not infer current security support from the hardware name alone. Retain the controller policy name, management authorization, certificate or trust workflow, authentication test and logging destination used at commissioning. Confirm the supported security behavior on the deployed software release. The hardware family alone must not be used to promise a feature or protocol that has not been validated.

Q-domain commissioning ledger

Maintain a Q-domain commissioning ledger with ten serials, ten switch ports and ten antenna-path checks. Record failures and substitutions against the affected row so one successful AP cannot be used as evidence that the entire eco-pack is suitable.

Lifecycle and migration evidence

Cisco's support site lists an end-of-life announcement for the Cisco Aironet 3800 Series. Confirm current support dates, controller compatibility and the approved replacement path before treating available stock as suitable for a new deployment.

Related 3802P external-antenna access point records

• AIR-AP3802P-EK910
• AIR-AP3802P-FK910
• AIR-AP3802P-HK910

Official evidence: Cisco Aironet 3800 Series data sheet, Cisco Aironet 3800 Series getting started guide, and Cisco end-of-life notices.