AIR-AP3802E-NK910 - Cisco Aironet 3800e Access Point

AIR-AP3802E-NK910 Order Identity

AIR-AP3802E-NK910 is a Cisco Aironet 3800 Series, controller-based 802.11ac Wave 2 access point order. This exact SKU is a 3802E external-antenna access point, carries regulatory-domain token N, and uses a fixed-domain 10-unit eco-pack.

Antenna and quantity boundary

External antennas are required and must be selected as separate, compatible order items. Build an antenna bill of materials that records connector, gain, pattern, cable loss, mounting hardware and local radio limits before release.

Cisco identifies the K910 order form as an eco-pack containing 10 access points; carton-level receiving must reconcile all ten serial numbers.

This is a non-C fixed-domain order form. Receiving must match the exact domain-bearing SKU and must not substitute a configurable or different-domain line without approval.

Regulatory-domain control

The order carries regulatory-domain token N. Treat that token as an identifier, not a country name. Complete destination-country verification and RF acceptance evidence against Cisco's current compliance resources before shipment or activation.

Cisco uses the variable regulatory-domain position in its ordering structure. Deployment eligibility must be checked for the destination country; this page does not infer a country mapping from token N.

Controller readiness

Record the intended Cisco wireless controller, supported software train and join method. Validate the AP on a staging network before changing the production RF plan. The acceptance file should identify the controller address, discovery path, AP authorization method and the release evidence used for approval. Capture the first successful join, configuration download and radio state, then remove any temporary staging authorization. This makes a later controller migration traceable without claiming that every software release supports the hardware.

Power budget

Confirm the switch port's negotiated PoE mode, available power, cable length and LLDP behavior. Keep the measured power result with commissioning evidence. Measure the power state after both radios and production features are active, not only while the unit is idle. Record switch model, port, power class, negotiated result and any feature reduction shown by the controller. If an injector is proposed, verify its Cisco support and place it in the maintained bill of materials.

Multigigabit uplink

The 3800 Series supports multigigabit Ethernet. Verify the switch port, cabling category, negotiated rate and error counters instead of assuming a 2.5 or 5 Gbps link. Commissioning should preserve the negotiated Ethernet rate, cable-test result, packet errors and switch configuration. Where the access switch is limited to 1 Gbps, state that design choice explicitly instead of presenting multigigabit capability as achieved throughput. Recheck negotiation after patch-cord or switch changes.

Replacement planning

Cisco lists the 3800 Series in its end-of-life notices. Record the permitted service horizon, replacement trigger and successor design with this purchase. Document the event that ends further 3802 deployment, the approved successor family and any controller coexistence constraint. Include funding, survey impact and installation sequencing. If the item is purchased as a spare, set a final-use date so old inventory does not silently outlive the network's supported architecture.

Spare policy

State whether the unit is production capacity, a cold spare or a replacement. Define firmware, storage, periodic test and ownership requirements for unused stock. A spare should have a named site scope, compatible controller image, storage condition and periodic power-on test. Record whether its regulatory domain, antenna form and mounting kit match the protected population. Before use, repeat compliance and software checks because suitability can change while the unit is held in stock.

Site acceptance

Commission association, authentication, roaming, uplink negotiation and monitoring at the intended location. Preserve results that can be compared after later changes. The handover record should contain client authentication, DHCP and DNS checks, roaming evidence, controller alarms, switch-port counters and a monitoring owner. Test from representative client types in the intended coverage area. Acceptance is incomplete when the AP merely joins the controller but user and operational paths remain unverified.

Lifecycle and migration evidence

Cisco's support site lists an end-of-life announcement for the Cisco Aironet 3800 Series. Confirm current support dates, controller compatibility and the approved replacement path before treating available stock as suitable for a new deployment.

Related 3802E external-antenna access point records

• AIR-AP3802E-G-K9
• AIR-AP3802E-H-K9
• AIR-AP3802E-K-K9

Official evidence: Cisco Aironet 3800 Series data sheet, Cisco Aironet 3800 Series getting started guide, and Cisco end-of-life notices.