AIR-AP3802E-BK910C Cisco Aironet 3800e Enterprise WiFi 5 AP 10-Pack

AIR-AP3802E-BK910C exact order identity

AIR-AP3802E-BK910C is a controller-based Cisco Aironet 3800 Series 802.11ac Wave 2 access-point order. The PID selects the 3802E access point for external antennas, configurable ten-unit K910C eco-pack and regulatory token B.

Antenna architecture

The 3802E requires separately selected compatible external antennas; connector fit alone is not an approved RF design. Record antenna PID, connector use, gain, pattern, cable loss, mounting, grounding and country approval.

Quantity and configuration boundary

Cisco identifies K910C as a configurable ten-access-point eco-pack. Preserve the selected regulatory-domain evidence and reconcile ten physical units independently.

B regulatory evidence

The domain token is not a country name. Match the B-domain carton label to the purchase line before serial assignment, then archive the dated compliance lookup.

Build the B-domain record around quotation-to-asset traceability. Preserve the authorized line, received label, chassis serial, assigned site and reviewer as one chain. If the controller later moves to another country configuration, open a new approval event rather than overwriting the original evidence; the history should explain both the purchased identity and every deployment decision.

Controller, PoE and uplink boundary

Validate the exact controller release and CAPWAP join before deployment. Preserve negotiated PoE, multigigabit Ethernet rate, cable certification and error counters; family capability does not prove the installed switch and cable path achieve that rate.

Lifecycle and migration decision

Cisco lists 2022-10-31 as end of sale and 2027-10-31 as last support for the Aironet 3800 Series, with Catalyst 9130AX as the replacement direction. Available inventory does not extend those dates.

Deployment evidence worksheet

Country approval retention

Save the Cisco compliance lookup result, lookup date, deployment country, approved regulatory token and reviewer. If the destination changes, stop and repeat the approval rather than moving the unit on the strength of an earlier purchase. Compare the controller country setting and available channels with the retained evidence. Regulatory eligibility is a deployment condition and cannot be inferred from connector fit, stock location or a similar-looking part number. Save the Cisco country lookup and controller country setting with the exact regulatory token.

Controlled spare policy

If purchased as a spare, name the protected site population, compatible controller image, storage location, storage conditions and periodic power-on test. Confirm that regulatory token, antenna architecture and mounting parts match the population it protects. Set a final-use review date. A stored unit can become unsuitable while untouched because controller software, country approval, certificates or network architecture may change. Test stored spares against controller release, PoE, domain, antenna and mounting dependencies.

Authentication path test

Commission representative clients through association, authentication, address assignment, DNS and application reachability. Preserve the identity policy used, test client type, result and relevant controller logs. An access point that joins its controller has not yet demonstrated the user path. Repeat the test after any controller, certificate or authentication-service change and retain failures separately from RF or switch-port evidence. Commission association, authentication, addressing, DNS and application reachability on representative clients.

Roaming acceptance

Define the neighboring access points and client types used for roaming validation. Record handoff behavior, interruption observed, authentication result and controller events along the intended movement path. Compare the outcome with the site's design target rather than declaring success from static association. Where this unit replaces an older AP, test both entry and exit from its cell so a local improvement does not hide a boundary problem. Document roaming path, neighboring cells, client type and controller events at each cell boundary.

Change-window controls

Document staging evidence, production window, installer, rollback owner and measurable success criteria. Preserve the prior controller or AP state needed for recovery. After the change, close temporary credentials, compare authentication, monitoring and RF results with the approved baseline, and record the final decision. The work is not complete merely because the unit powers on or appears in a controller list. Rollback must restore controller assignment, country setting, switch port and prior RF service.

Replacement dependency map

Map this unit to controller, licenses, authentication services, switch power, cable, bracket, antenna design and monitoring objects. For an end-of-sale platform, state which dependencies can be reused by the planned Catalyst migration and which require change. A nominal access-point replacement can fail when the surrounding platform was never inventoried. Keep the map with the asset rather than only in a one-time project file. Compare Catalyst 9130AX controller, power, cabling, antenna, mounting and coverage dependencies.

Receiving inspection

At receipt, compare model label, regulatory token, antenna form, quantity, serials and visible condition with the authorized order. Photograph labels before cartons are separated. Quarantine shortages, mixed units, damaged connectors or unapproved substitutions. Do not rely on a distributor description as evidence that the exact Cisco order arrived. Close the inspection only when every physical unit is accounted for. Receiving must distinguish 3802E from 3802I and single-unit from ten-unit order before release.

Handover completeness

The handover package should include exact order identity, destination approval, serial record, controller evidence, switch port, mounting or antenna record, user-path tests and named operational owners. Review the package with the receiving team and list unresolved exceptions. A unit is not operationally accepted when important evidence remains only in installer notes, email attachments or an unowned temporary dashboard. Handover should include PID, all serials, compliance result, controller, antenna record and lifecycle owner.

Related Aironet 3802 orders

• AIR-AP3802E-B-K9 - compare antenna, quantity, configuration and domain evidence.
• AIR-AP3802I-NK910C - compare antenna, quantity, configuration and domain evidence.
• AIR-AP3802I-TK910C - compare antenna, quantity, configuration and domain evidence.

Official evidence: Cisco Aironet 3800 data sheet; Cisco getting-started guide; Cisco 3800 lifecycle bulletin; Cisco support page; and Cisco compliance lookup.