C9120AXI-EWC-K Cisco Catalyst 9120 Dual Concurrent Access Point

C9120AXI-EWC-K exact order identity

C9120AXI-EWC-K is a Cisco Catalyst 9120AX Series indoor Wi-Fi 6 access point with integrated antennas. The exact PID combines the I antenna form, a access-point order carrying the Embedded Wireless Controller software image and regulatory-domain token K.

Antenna and installation boundary

Cisco documents four integrated dual-band antennas, four additional single-band 5 GHz antennas used in dual-5-GHz mode, one 2.4 GHz IoT antenna and one dual-band auxiliary-radio antenna. No external antenna is selected by this PID. Mounting position, enclosure orientation and the post-install RF survey are therefore part of the acceptance evidence. The integrated-antenna order does not require an external antenna bill of materials.

Controller-image boundary

Cisco defines the EWC PID as the same antenna-form access point with a Cisco Embedded Wireless Controller software image. Cisco ended sale of EWC-AP on 29 November 2024 and identifies IOS XE 17.15.x as the final EWC-AP train. Its bulletin permits conversion to lightweight CAPWAP mode for controller-based operation, subject to the applicable support terms.

K regulatory-domain evidence

Cisco uses the final PID letter as a regulatory-domain identifier and requires customers to verify approval for the country of use. The letter is not a country name. Tie the K-domain purchase line to the controller country configuration and the post-join enabled-channel export.

Center the K-domain package on channel-state evidence. Retain the Cisco country lookup and controller country configuration, then export the enabled-channel state after the AP joins. Store the output with exact PID, serial and survey reference. Repeat the comparison after controller upgrades so a software change cannot silently separate the live radio state from the approved order.

Power and wired-uplink boundary

The family has one 100/1000/2500 Multigigabit Ethernet uplink. Cisco lists full 4x4 radio operation, 2.5-Gigabit Ethernet and USB with 802.3at; under 802.3af both radios reduce to 1x1, Ethernet reduces to 1 GbE and USB is disabled.

EWC lifecycle decision

Cisco ended sale of EWC-AP on 29 November 2024, lists IOS XE 17.15.x as the final EWC-AP software train and gives 30 November 2029 as the last support date. The lifecycle bulletin says these APs can be converted to lightweight CAPWAP mode; record that conversion and controller plan rather than treating the EWC suffix as a permanent operating requirement.

Deployment evidence worksheet

Controller join evidence

Stage the access point on the controller release intended for production. Retain the controller model, software version, discovery path, authorization method and first successful CAPWAP join. Confirm that configuration download completes and that both radios reach an expected operational state. Remove any temporary staging authorization before handover. This evidence separates an orderable access point from a unit that has actually been proven compatible with the planned controller environment. For the 9120AX, keep the controller model, release and first successful CAPWAP join with the exact regulatory-domain PID.

Ethernet and cabling proof

Preserve the permanent-link test, patch-lead identities, switch port, negotiated Ethernet rate and error counters. Investigate pair faults, excessive length or rate fallback before wireless acceptance begins. A link light only proves connectivity at some rate; it does not demonstrate the intended uplink performance. Tie the cable result to the AP serial so a later throughput problem can be separated from radio, controller and wired-path causes. The wired acceptance result should show whether the single IEEE 802.3bz uplink negotiated at 100 Mbps, 1 Gbps or 2.5 Gbps.

Survey-to-install reconciliation

Attach the approved RF survey location, mounting height, orientation, expected client density, channel width and neighboring-radio assumptions to the order. After installation, compare measured coverage and interference with that design. If ceiling construction, antenna placement or obstructions changed, document the deviation and repeat the affected measurements. This provides a site-specific acceptance reason for the exact unit instead of relying on a family data sheet alone. Relate the installed radio mode to the survey because the flexible radio can serve 2.4/5 GHz or participate in a dual-5-GHz design.

Serial-level asset control

Capture chassis serial, base MAC address, carton reference, deployment site, controller assignment and asset owner. Reconcile the identifiers against the purchase line before activation. Multi-unit cartons require an entry for every physical access point; a carton SKU alone cannot show which unit was installed, held as a spare or returned. This record is also needed to trace support entitlement, replacement history and monitoring ownership. Asset identity must preserve AXI, AXE or AXP, the EWC state and the final domain token because each field changes the procurement boundary.

Authentication path test

Commission representative clients through association, authentication, address assignment, DNS and application reachability. Preserve the identity policy used, test client type, result and relevant controller logs. An access point that joins its controller has not yet demonstrated the user path. Repeat the test after any controller, certificate or authentication-service change and retain failures separately from RF or switch-port evidence. Test association, authentication, address assignment and application reachability after the 9120AX reaches its final controller and radio state.

Capacity observation

Define the expected concurrent clients, application mix, airtime utilization and channel-width assumptions for this location. After commissioning, capture radio utilization, retry behavior and representative throughput during a meaningful load period. Compare the observation with the survey design and state any shortfall. A peak link rate from a data sheet is not a site capacity result and should not replace measured operating evidence. Capacity acceptance should use observed clients, channel width, airtime and retries rather than the family's maximum over-the-air rate.

Replacement dependency map

Map this unit to controller, licenses, authentication services, switch power, cable, bracket, antenna design and monitoring objects. For an end-of-sale platform, state which dependencies can be reused by the planned Catalyst migration and which require change. A nominal access-point replacement can fail when the surrounding platform was never inventoried. Keep the map with the asset rather than only in a one-time project file. For EWC orders, record the 17.15.x support ceiling and a CAPWAP conversion decision; for non-EWC orders, record the external controller lifecycle.

Handover completeness

The handover package should include exact order identity, destination approval, serial record, controller evidence, switch port, mounting or antenna record, user-path tests and named operational owners. Review the package with the receiving team and list unresolved exceptions. A unit is not operationally accepted when important evidence remains only in installer notes, email attachments or an unowned temporary dashboard. The handover package should contain the exact PID, serial, compliance result, controller assignment, antenna or mounting record and named owner.

Related Catalyst 9120 order records

• C9120AXP-K - compare antenna form and domain evidence.
• C9120AXE-K - compare antenna form and domain evidence.
• C9120AXP-EWC-K - compare antenna form and domain evidence.

Official evidence: Cisco Catalyst 9120AX data sheet; Cisco Catalyst 9120AX getting-started guide; Cisco EWC-AP lifecycle bulletin; Cisco wireless compliance tool.