AIR-AP1852E-I-K9C Cisco Aironet 1852e WiFi 5 4x4 MIMO AP

AIR-AP1852E-I-K9C exact order identity

AIR-AP1852E-I-K9C is a 1852e indoor access point for separately purchased external antennas in the Cisco Aironet 1850 Series. This exact SKU combines regulatory-domain token I with a single-unit configurable K9C order. The platform is a dual-band 802.11ac Wave 2 access point with four 5 GHz spatial streams in single-user operation and three in multiuser operation.

Antenna and environmental boundary

Cisco states that external antennas are sold separately and certifies the platform for antenna gains up to 6 dBi at both 2.4 and 5 GHz. Record the approved Cisco antenna part numbers, four radio paths, gain, pattern, cable loss, connectors and mounting orientation. A compatible connector alone is not regulatory or RF-design evidence.

Order and controller boundary

Cisco lists K9C as a configurable controller-based order, and its lifecycle table describes affected K9C lines as Mobility Express products. Retain the final domain and software role on the quotation and received unit. Prove the intended controller or Mobility Express state instead of inferring it from the suffix alone.

I regulatory-domain evidence

Cisco lists this profile as 2.4 GHz channels 1-13 and the 5.180-5.320 GHz lower block. The I profile listed by Cisco is confined to the lower 5 GHz block. Designs that depend on middle or upper 5 GHz capacity need revision before this SKU can be approved. Commission with a lower-block-only channel plan and preserve the controller export. Recalculate co-channel reuse if the pre-purchase survey assumed additional 5 GHz spectrum.

Procurement inference: the lower-block-only 5 GHz plan places a tighter ceiling on channel diversity than profiles with middle or upper groups. Capacity approval should therefore show the client load, channel width and reuse plan that fit within this listed range. If the access point is a spare, verify that the protected population uses the same I-domain constraints before assigning it to emergency replacement stock.

Power and interface boundary

The 1852 provides a PoE Gigabit uplink and a Gigabit AUX port for link aggregation. Cisco states that 802.3af disables AUX and USB on both antenna forms and reduces the 1852e 2.4 GHz radio from 3x4 to 2x3. Record negotiated power before promising the complete interface and radio state.

Deployment evidence worksheet

Ethernet and cabling proof

Preserve the permanent-link test, patch-lead identities, switch port, negotiated Ethernet rate and error counters. Investigate pair faults, excessive length or rate fallback before wireless acceptance begins. A link light only proves connectivity at some rate; it does not demonstrate the intended uplink performance. Tie the cable result to the AP serial so a later throughput problem can be separated from radio, controller and wired-path causes. The platform has one PoE Gigabit interface and one Gigabit AUX interface used for link aggregation, so preserve both link states and the power condition under which AUX is available.

Survey-to-install reconciliation

Attach the approved RF survey location, mounting height, orientation, expected client density, channel width and neighboring-radio assumptions to the order. After installation, compare measured coverage and interference with that design. If ceiling construction, antenna placement or obstructions changed, document the deviation and repeat the affected measurements. This provides a site-specific acceptance reason for the exact unit instead of relying on a family data sheet alone. Relate the survey result to the 1852's 4x4:4 single-user and 4x4:3 multiuser 5 GHz design rather than treating the published 1.7 Gbps PHY rate as measured site throughput.

Mechanical installation record

List the bracket, ceiling or wall interface, enclosure requirement, safety restraint, service clearance and cable-entry plan before scheduling installation. Receiving should identify missing mechanical items before the access point reaches site. Photograph the mounted label and final cable entry, then record how the unit can be reached for replacement. A complete electronic order can still be an unusable deployment kit when mechanical dependencies are omitted. The 1852i and 1852e have different operating-temperature ranges, and an external-antenna deployment also requires a complete cable and mounting bill of materials.

Serial-level asset control

Capture chassis serial, base MAC address, carton reference, deployment site, controller assignment and asset owner. Reconcile the identifiers against the purchase line before activation. Multi-unit cartons require an entry for every physical access point; a carton SKU alone cannot show which unit was installed, held as a spare or returned. This record is also needed to trace support entitlement, replacement history and monitoring ownership. If the product came from a ten-unit pack, the 1852 carton identity must be expanded into ten individual records before support, return or replacement handling.

Software lifecycle file

Record the controller release approved for this unit, the source used to verify support, the last tested date and the owner for software advisories. Available hardware does not prove compatibility with a current or future controller train. Review Cisco support information before every expansion or replacement. The lifecycle file should also state when this Aironet generation must leave service and which surrounding dependencies need migration. Cisco ended 1850 Series software maintenance in 2023, so controller compatibility evidence is especially important for inventory purchased late in the lifecycle.

Controlled spare policy

If purchased as a spare, name the protected site population, compatible controller image, storage location, storage conditions and periodic power-on test. Confirm that regulatory token, antenna architecture and mounting parts match the population it protects. Set a final-use review date. A stored unit can become unsuitable while untouched because controller software, country approval, certificates or network architecture may change. A spare 1852 must be checked against the protected controller release, certificate behavior, regulatory domain, antenna form and 2027 support cutoff before assignment.

Monitoring handover

Assign owners for AP reachability, controller join failures, radio utilization, client health and switch-port errors. Confirm that the exact serial appears in inventory and monitoring, then test the alert path. Record dashboard object, notification route and escalation owner. Telemetry that is not tied to an owned asset does not provide a reliable service baseline and will not support later comparison after channel or software changes. Monitoring should identify the 1852 serial, controller object, both Ethernet interfaces, radio health and the team responsible for end-of-support migration.

Change-window controls

Document staging evidence, production window, installer, rollback owner and measurable success criteria. Preserve the prior controller or AP state needed for recovery. After the change, close temporary credentials, compare authentication, monitoring and RF results with the approved baseline, and record the final decision. The work is not complete merely because the unit powers on or appears in a controller list. Rollback must account for controller image alignment, country configuration and any Mobility Express primary role, not only the physical swap.

Lifecycle decision

Cisco ended sale of the Aironet 1850 Series on 1 May 2022, ended software maintenance on 1 May 2023 and lists 30 April 2027 as the last support date. Cisco identifies Catalyst 9115AX as the migration family. Available inventory does not extend those milestones.

Related Aironet 1852 order records

• AIR-AP1852I-IK910C - compare antenna form and domain evidence.
• AIR-AP1852I-I-K9C - compare antenna form and domain evidence.
• AIR-AP1852E-I-K9 - compare order form and domain evidence.

Official evidence: Cisco Aironet 1850 Series data sheet; Cisco Aironet 1850 hardware guide; Cisco Aironet 1850 lifecycle bulletin; and Cisco wireless compliance tool.