The Cisco Catalyst 9130AX series wireless access point is a dual-band, dual-concurrent, enterprise 802.11ax (Wi-Fi 6) AP. This AP series has two models, one with integrated antennas and the other with external antennas, which are designed to use both 2.4 GHz and the 5 GHz bands.
Cisco Catalyst 9130 Series key features
● Next-generation Wi-Fi 6 (802.11ax) access points with 4x4 Multiple-Input Multiple-Output (MIMO) and four spatial streams:
◦ 8x8:8 single or dual 4x4:4 on 5 GHz and downlink/uplink Orthogonal Frequency-Division Multiple Access (OFDMA)
◦ 4x4:4 on 2.4 GHz with multiuser MIMO (MU-MIMO) and downlink/uplink OFDMA
● Cisco DNA ready
● Cisco RF Application-Specific Integrated Circuit (ASIC) with next-generation Cisco CleanAir® and upgradable RF features
● Built-in Bluetooth Low Energy (BLE) radio (Bluetooth 5.0)
● Multigigabit Ethernet (1 Gbps, 2.5 and 5 Gbps)
● USB
● Supports up to 500 Wi-Fi devices
● IoT ready (BLE)
● Internal and external antenna options
● Operating temperature for 9130I: -32° to 122°F (0° to 50°C)
● Operating temperature for 9130E: -4° to 122°F (-20° to 50°C)
| Software | Catalyst 9130AXI | ||||||||||||
| ● Cisco Unified Wireless Network Software Release 8.10.x or later | |||||||||||||
| ● Cisco IOS XE Software Release 16.12.1 with AP Device Pack, or later | |||||||||||||
| Supported wireless LAN controllers | ● Cisco Catalyst 9800 Series Wireless Controllers | ||||||||||||
| ● Cisco 3504, 5520, and 8540 Wireless Controllers and Cisco Virtual Wireless Controller | |||||||||||||
| 802.11n version 2.0 (and related) capabilities | ● 4x4 MIMO with four spatial streams | ||||||||||||
| ● Maximal Ratio Combining (MRC) | |||||||||||||
| ● 802.11n and 802.11a/g | |||||||||||||
| ● 20- and 40-MHz channels | |||||||||||||
| ● PHY data rates up to 1.5 Gbps (40 MHz with 5 GHz and 20 MHz with 2.4 GHz) | |||||||||||||
| ● Packet aggregation: Aggregate MAC Protocol Data Unit (A-MPDU) (transmit and receive), Aggregate MAC Service Data Unit (A-MSDU) (transmit and receive) | |||||||||||||
| ● 802.11 Dynamic Frequency Selection (DFS) | |||||||||||||
| ● Cyclic Shift Diversity (CSD) support | |||||||||||||
| 802.11ac | ● 8x8 downlink MU-MIMO with eight spatial streams | ||||||||||||
| ● MRC | |||||||||||||
| ● 802.11ac beamforming | |||||||||||||
| ● 20-, 40-, 80-, and 160-MHz channels | |||||||||||||
| ● PHY data rates up to 3.4 Gbps (8x8 80 MHz or Dual 4x4 80+80 MHz on 5GHz) | |||||||||||||
| ● Packet aggregation: A-MPDU (transmit and receive), A-MSDU (transmit and receive) | |||||||||||||
| ● 802.11 DFS | |||||||||||||
| ● CSD support | |||||||||||||
| ● Wi-Fi Protected Access (WPA) 3 support | |||||||||||||
| 802.11ax | ● 8x8 uplink/downlink MU-MIMO with eight spatial streams | ||||||||||||
| ● Uplink/downlink OFDMA | |||||||||||||
| ● TWT | |||||||||||||
| ● BSS coloring | |||||||||||||
| ● MRC | |||||||||||||
| ● 802.11ax beamforming | |||||||||||||
| ● 20-, 40-, 80-, and 160-MHz channels | |||||||||||||
| ● PHY data rates up to 5.38 Gbps (8x8 80 MHz or Dual 4x4 80+80 MHz on 5GHz and 4x4 20 MHz on 2.4) | |||||||||||||
| ● Packet aggregation: A-MPDU (transmit and receive), A-MSDU (transmit and receive) | |||||||||||||
| ● 802.11 DFS | |||||||||||||
| ● CSD support | |||||||||||||
| ● WPA3 support | |||||||||||||
| Integrated antenna | ● 2.4 GHz: Peak gain 4 dBi, internal antenna, omnidirectional in azimuth | ||||||||||||
| ● 5 GHz: Peak gain 6 dBi, internal antenna, omnidirectional in azimuth | |||||||||||||
| External antenna with smart antenna connector | ● Supports Self-Identifiable Antennas (SIA) on the smart antenna connector | ||||||||||||
| ● Smart antenna connector is a compact multi-RF connector with 8-DART interface | |||||||||||||
| ● Requires the AIR-CAB002-D8-R= 2 ft smart antenna connector when used with antennas with a RP-TNC connector | |||||||||||||
| ● Requires the AIR-CAB003-D8-N= 3 ft smart antenna connector when used with AIR-ANT2513P4M-N= antenna | |||||||||||||
| Interfaces | ● 1x 100, 1000, 2500, 5000 Multigigabit Ethernet (RJ-45) | ||||||||||||
| ● Management console port (RJ-45) | |||||||||||||
| ● USB 2.0 at 4.5W | |||||||||||||
| Indicators | ● Status LED indicates boot loader status, association status, operating status, boot loader warnings, and boot loader errors | ||||||||||||
| Dimensions (W x L x H) | ● Access point (without mounting brackets): | ||||||||||||
| ◦ C9130AXI: 8.9 x 8.9 x 1.88 in. (22.6 x 22.6 x 4.8 cm) | |||||||||||||
| Weight | Cisco Catalyst 9130AXI | ||||||||||||
| ● 3.2 lb. (1.45 kg) | |||||||||||||
| Input power requirements | ● 802.3at Power over Ethernet Plus (PoE+), 802.3bt Cisco Universal PoE (Cisco UPOE) | ||||||||||||
| ● Cisco power injector, AIR-PWRINJ6= | |||||||||||||
| ● 802.3af PoE | |||||||||||||
| ● Cisco power injector, AIR-PWRINJ5= (Note: This injector supports only 802.3af) | |||||||||||||
| Catalyst 9130AXI | |||||||||||||
| Power source | 2.4-GHz radio | 5-GHz radio | Link speed | USB | Max PoW Power Consumption | ||||||||
| 802.3at (PoE+) | 4x4 | 8x8 | 5G | N | 25.5W | ||||||||
| 802.3at (PoE+) | 4x4 | 4x4 | 5G | Y [4.5W] | 25.5W | ||||||||
| 802.3bt (Cisco UPOE) | 4x4 | 8x8 | 5G | Y [4.5W] | 30.5W | ||||||||
| Environmental | Cisco Catalyst 9130AXI | ||||||||||||
| ● Nonoperating (storage) temperature: -22° to 158°F (-30° to 70°C) | |||||||||||||
| ● Nonoperating (storage) altitude test: 25˚C, 15,000 ft (4600 m) | |||||||||||||
| ● Operating temperature: 32° to 122°F (0° to 50°C) | |||||||||||||
| ● Operating humidity: 10% to 90% (noncondensing) | |||||||||||||
| ● Operating altitude test: 40˚C, 9843 ft (3000 m) | |||||||||||||
| Note: When the ambient operating temperature exceeds 40°C, the access point will shift from 8x8 to 4x4 on the 5 GHz radio, uplink Ethernet will downgrade to 1 Gigabit Ethernet; however, the USB interface will remain enabled. | |||||||||||||
| System memory | ● 2048 MB DRAM | ||||||||||||
| ● 1024 MB flash | |||||||||||||
| Warranty | Limited lifetime hardware warranty | ||||||||||||
| Available transmit power settings | 2.4 GHz | 5 GHz | |||||||||||
| ● 23 dBm (200 mW) | ● 26 dBm (400 mW) | ||||||||||||
| ● -4 dBm(0.39 mW) | ● -1 dBm (0.79 mW) | ||||||||||||
| Compliance standards | ● Safety: | ● Radio: | |||||||||||
| ◦ IEC 60950-1 | ◦ EN 300 328 (v2.1.1) | ||||||||||||
| ◦ EN 60950-1 | ◦ EN 301 893 (v2.1.1) | ||||||||||||
| ◦ UL 60950-1 | ◦ AS/NZS 4268 (rev. 2017) | ||||||||||||
| ◦ CAN/CSA-C22.2 No. 60950-1 | ◦ 47 CFR FCC Part 15C, 15.247, 15.407 | ||||||||||||
| ◦ AS/NZS60950.1 | ◦ RSP-100 | ||||||||||||
| ◦ UL 2043 | ◦ RSS-GEN | ||||||||||||
| ◦ Class III equipment | ◦ RSS-247 | ||||||||||||
| ● Emissions: | ◦ China regulations SRRC | ||||||||||||
| ◦ CISPR 32 (rev. 2015) | ◦ LP0002 (rev 2018.1.10) | ||||||||||||
| ◦ EN 55032 (rev. 2012/AC:2013) | ◦ Japan Std. 33a, Std. 66, and Std. 71 | ||||||||||||
| ◦ EN 55032 (rev. 2015) | ● RF safety: | ||||||||||||
| ◦ EN61000-3-2 (rev. 2014) | ◦ EN 50385 (rev. Aug 2002) | ||||||||||||
| ◦ EN61000-3-3 (rev. 2013) | ◦ ARPANSA | ||||||||||||
| ◦ KN61000-3-2 | ◦ AS/NZS 2772 (rev. 2016) | ||||||||||||
| ◦ KN61000-3-3 | ◦ EN 62209-1 (rev. 2016) | ||||||||||||
| ◦ AS/NZS CISPR 32 Class B (rev. 2015) | ◦ EN 62209-2 (rev. 2010) | ||||||||||||
| ◦ 47 CFR FCC Part 15B | ◦ 47 CFR Part 1.1310 and 2.1091 | ||||||||||||
| ◦ ICES-003 (rev. 2016 Issue 6, Class B) | ◦ RSS-102 | ||||||||||||
| ◦ VCCI-CISPR 32 | ● IEEE standards: | ||||||||||||
| ◦ CNS (rev. 13438) | ◦ IEEE 802.3 | ||||||||||||
| ◦ KN-32 | ◦ IEEE 802.3ab | ||||||||||||
| ◦ QCVN 118:2018/BTTTT | ◦ IEEE 802.3af/at | ||||||||||||
| ● Immunity: | ◦ IEEE 802.11a/b/g/n/ac/ax | ||||||||||||
| ◦ CISPR 24 (rev. 2010) | ◦ IEEE 802.11h, 802.11d | ||||||||||||
| ◦ EN 55024 + AMD 1(rev. 2010) | ● Security: | ||||||||||||
| ◦ EN 55035: 2017 | ◦ 802.11i, (WPA2, WPA3 | ||||||||||||
| ◦ KN35 | ◦ 802.1X | ||||||||||||
| ● Emissions and immunity: | ◦ Advanced Encryption Standard (AES) | ||||||||||||
| ◦ EN 301 489-1 (v2.1.1 2017-02) | ● Extensible Authentication Protocol (EAP) types: | ||||||||||||
| ◦ EN 301 489-17 (v3.1.1 2017-02) | ◦ EAP-Transport Layer Security (TLS) | ||||||||||||
| ◦ QCVN (18:2014) | ◦ EAP-Tunneled TLS (TTLS) or Microsoft Challenge Handshake Authentication Protocol (MSCHAP) v2 | ||||||||||||
| ◦ QCVN 112:2017/BTTTT | ◦ Protected EAP (PEAP) v0 or EAP-MSCHAP v2 | ||||||||||||
| ◦ KN 489-1 | ◦ EAP-Flexible Authentication via Secure Tunneling (EAP-FAST) | ||||||||||||
| ◦ KN 489-17 | ◦ PEAP v1 or EAP-Generic Token Card (GTC) | ||||||||||||
| ◦ EN 60601-1-2:2015 | ◦ EAP-Subscriber Identity Module (SIM) | ||||||||||||
| ◦ EN 61000-6-1: 2007 | |||||||||||||
| Data rate, transmit power, receive sensitivity | For more detailed information about data rate, transmit power, and receive sensitivity, please refer to the Cisco RF details. | ||||||||||||
| Transmit (Tx) power and receive (Rx) sensitivity | |||||||||||||
| 5-GHz primary radio | 5-GHz secondary radio | 2.4-GHz radio | |||||||||||
| Spatial streams | Number of active antennas | Total Tx power (dBm) | Rx sensitivity (dBm) | Total Tx power (dBm) | Rx sensitivity (dBm) | Total Tx power (dBm) | Rx sensitivity (dBm) | ||||||
| 802.11/11b | |||||||||||||
| 1 Mbps | 1 | 4 | – | – | – | – | 23 | -104 | |||||
| 11 Mbps | 1 | 4 | – | – | – | – | 23 | -96 | |||||
| 802.11a/g | |||||||||||||
| 6 Mbps | 1 | 4 | 23 | -100 | 23 | -99 | 23 | -98 | |||||
| 24 Mbps | 1 | 4 | 22 | -92 | 22 | -92 | 22 | -91 | |||||
| 54 Mbps | 1 | 4 | 21 | -84 | 21 | -83 | 20 | -82 | |||||
| 802.11n HT20 | |||||||||||||
| MCS0 | 1 | 4 | 23 | -99 | 23 | -99 | 23 | -98 | |||||
| MCS31 | 4 | 4 | 20 | -77 | 20 | -77 | 20 | -75 | |||||
| 802.11n HT40 | |||||||||||||
| MCS0 | 1 | 4 | 23 | -96 | 23 | -96 | – | – | |||||
| MCS31 | 4 | 4 | 20 | -75 | 20 | -75 | – | – | |||||
| 802.11ac VHT20 | |||||||||||||
| MCS0 | 1 | 4 | 23 | -100 | 23 | -99 | – | – | |||||
| MCS9 | 4 | 4 | – | – | – | – | – | – | |||||
| MCS0 | 1 | 8 | 26 | -102 | – | – | – | ||||||
| MCS8 | 8 | 8 | 23 | -73 | – | – | – | ||||||
| MCS9 | 8 | 8 | – | – | – | – | – | ||||||
| 802.11ac VHT40 | |||||||||||||
| MCS0 | 1 | 4 | 23 | -96 | 23 | -96 | – | – | |||||
| MCS9 | 4 | 4 | 19 | -69 | 19 | -69 | – | – | |||||
| MCS0 | 1 | 8 | 26 | -99 | – | – | – | ||||||
| MCS9 | 8 | 8 | 22 | -69 | – | – | – | ||||||
| 802.11ac VHT80 | |||||||||||||
| MCS0 | 1 | 4 | 23 | -93 | 23 | -93 | – | – | |||||
| MCS9 | 4 | 4 | 19 | -65 | 19 | -64 | – | – | |||||
| MCS0 | 1 | 8 | 26 | -95 | – | – | – | ||||||
| MCS9 | 8 | 8 | 22 | -65 | – | – | – | ||||||
| 802.11ac VHT160 | |||||||||||||
| MCS0 | 1 | 4 | 26 | -89 | – | – | – | ||||||
| MCS9 | 4 | 4 | 21 | -61 | – | – | – | ||||||
| 802.11ax HE20 | |||||||||||||
| MCS0 | 1 | 4 | 23 | -99 | 23 | -99 | 23 | -98 | |||||
| MCS11 | 4 | 4 | 18 | -66 | 18 | -66 | 17 | -65 | |||||
| MCS0 | 1 | 8 | 26 | -102 | – | – | – | ||||||
| MCS11 | 8 | 8 | 21 | -65 | – | – | – | ||||||
| 802.11ax HE40 | |||||||||||||
| MCS0 | 1 | 4 | 23 | -96 | 23 | -96 | – | – | |||||
| MCS11 | 4 | 4 | 18 | -63 | 18 | -62 | – | – | |||||
| MCS0 | 1 | 8 | 26 | -99 | – | – | – | ||||||
| MCS11 | 8 | 8 | 21 | -63 | – | – | – | ||||||
| 802.11ax HE80 | |||||||||||||
| MCS0 | 1 | 4 | 23 | -93 | 23 | -93 | – | – | |||||
| MCS11 | 4 | 4 | 17 | -59 | 17 | -59 | – | – | |||||
| MCS0 | 1 | 8 | 26 | -96 | – | – | – | ||||||
| MCS11 | 8 | 8 | 20 | -59 | – | – | – | ||||||
| 802.11ax HE160 | |||||||||||||
| MCS0 | 1 | 4 | 26 | -88 | – | – | – | ||||||
| MCS11 | 4 | 4 | 19 | -56 | – | – | – | ||||||
Low Price Guarantee | ![]() | Quality Assurance | |
![]() | Free CCIE Expert Technical Support | Commodity Refund Guarantee | |
Diversified and Flexible Transportation Services | ![]() | Standard Policy |